Aktueller Inhalt von Sylwester.

the worst part is that such you tube protects samsung , I tried to post my warning in the yt comments under the monitor tests and it is automatically deleted

I warn you about samsung monitors . I myself bought a g8 oled back in march last year and I was very happy with it , I have praised it more than once here on the forum , unfortunately my monitor will be affected by a case that very often happens to samsung curved monitors , namely the...

I will join the topic , admittedly offtopic but I warn you about samsung monitors . I myself bought a g8 oled back in march last year and I was very happy with it , I have praised it more than once here on the forum , unfortunately my monitor will be affected by a case that very often happens...

They also confirmed it to me, except that they stipulated that the technician will check whether the monitor was used properly, when I sent a return e-mail asking "what does it mean properly or not properly", I did not receive any more answer. :unsure: 1692033796 "No problems with standby mode...

gentlemen how does anyone have problems waking up the monitor after sleep , or how mine doesn't turn on with system startup , on reddit I found a solution , at least it works for me : you have to hold down the power key on the remote until the monitor restarts , then restart the system and the...

fellows, something went wrong in aquasuite, I have a Quadro, a long time ago I found instructions on how to create profiles, I created 3 profiles: quiet, efficient and max, which were responsible for the appropriate speed of the pump and fans, quiet - based on the water temperature it selects...

no U must drill hole 2,5mm and use Handtap m3 like this : it cost few euro it also depends on the thickness of the backplate, it would be good if it was at least 2mm, and tighten it gently because aluminum is a soft metal and you can break the thread. Choose the length of the screws so that...

MORA cools the liquid very well, but the problem is high flow restriction, that's why I decided on the Alphacool NexXxoS XT45 Full Copper 1080mm Radiator, it has much lower flow restrictions, thanks to which, in combination with two D5 pumps, I get high liquid flow and a significant drop in gpu...

sure that you can remedy , give your thermal pads in place of the core itself , just choose the right thickness , because I do not know what gap there is As for mounting the block to the backplate, I would do it the same way as you have mounted it on the previous card, I would drill four holes...

I order HY234 on Fruugo.nl becaus i actuall in Netherland , but i see that is also avaliable on fruugo.de https://www.fruugo.de/search/?q=thermal+putty# use this on rtx 4090 tuf , with ek waterblock , and I can recommend the results better to ek thermal pads , similar to deepcool thermal pads...

first of all, welcome to everyone going back to the post quoted , the fact that bykski blocks do not even have thermo pads under the backplate , does not speak well of them at all , on the contrary , myself on rtx 4090 tuf on the backplate from ek block I had simply laid (without tightening , or...

I do not know if this is a problem, cleaning the thermal putty requires more effort than removing the thermopads , yes you need to use isopropanol, but you do not need to bathe the entire card, roughly collect with a stick, you can use it back, I clean the rest with a soft brush that I soak in...

Instead of bothering with thermopads , isn't it better to use thermal putty? a month ago on my 4090 tuf I applied hy230 thermal putty , also ptm7950 on the core , I am very satisfied with the results , delta water to gpu temperature is 16'C with an average consumption of 470W , delta of water...

on my rtx 4090 tuf I have no such reading , supposedly the latest version of hwinfo , do I need to activate something in the program ?

Gentlemen I saw in earlier posts that 4090 strix shows in hwinfo vrm temps , is this possible with 4090 tuf ?