Suchergebnisse

Thank you for your time Sorry I did just a small typo - LLC3 while SVID Trained set auto values to AC 0.54, DC 1.1 Here is my V/F:

Hello and thank you I did some tests with the updated curve, I am not sure how to interpret the results. All tests are done with SVID = trained, 364A ICCMAX. I also tests original CPU V/F, without any offsets, same ICCMAX, SVID as Trained, AC/DC auto (it sets 0.55AC 1.1DC) With the improved...

So I am back in the game. I decided to replace the CPU for a new one. Finally got the new one CPU and posting progress. The new CPU has slightly better V/F I think. Anyway: The only stable config with your custom V/F is LLC 3, IA_AC 1.0, IA_DC 1.1 ( = auto). R23 pass 10 minutes, Y-C SFT VST VT3...

Yes, you were right. I am starting from scratch, memory all auto. So far LLC 4, AC 0.3 / DC 1.02 and it is fully stable. This, with my old 8000 memOC, was unstable. However I am not yet playing with the V/F curve and SVID is still AUTO. Want to solve LLC AC DC first. Sorry for not posting any...

Yes, I won't give up. I'll do everything I can. I wonder why it is the way it is. Thank you.

So I did one more "experiment". All memory settings and frequency on auto, so memory run 5600 CL46. CPU settings, V/F settings etc all is exactly as you said. R23 is still unstable. And another experiment, leaved memory setting at 8000 unchanged, but with SVID auto, load lines auto and V/F auto...

Can´t make it works, every combination is unstable. CPU_AUX to 1.9V did not help as well.

Yes, everything is correct. For sure I am as well uploading BIOS with 0.6 IA_AC in text form if you may check if I did a mistake. 0.6 IA_AC = Cinebench R23 crash right at the start and PC restarts. Y-Cruncher 0.8.2 2.5b restarts PC right at the start. 0.8 IA_AC = Cinebench R23 lasts usually few...

Not going too well. Random freezes right when R23 starts, same Geekbench Y-Cruncher 2.5b. When increased IA_AC Loadline from 0.6 to 0.8, still the same. Should I go higher, or change something else please?

Reading old posts, but I am still lost. This is what I get if I use the Tool and "generate" curve.

Ok, this is very far beyond my experience, but I will try. IA_AC Loadline is set to 0.6 IA CEP and SA CEP to disabled. CPU Load-line Calibration is still Auto (says level 3), is it OK? I know how to change the V(F curve, but I have no idea what values I should put there.

Thank you a lot, much appreciated! I did not modify the V/F curve at all, I passed that CPU part. About CPU I did only setting ASUS MultiCore Enhancement to Enable, and set CPU Core/Cache Current Limit Max. to the 400A. Now I will set the 155W PL2, 140W PL1 with ICCMAX 280A as you recommended...

Thanks a lot. This is with power Watt unlimited, capped 400A. I guess I can limit PL1 power watts to maybe 150W and PL2 to 162W and 280A cap then. How long I should set the time in seconds, it´s the question. And I will start with TM5 + VST/VT3. Let the fun begin 8-)

Not at all. It's more complicated. The PC is in the bedroom, and the vents are set to low noise, CPU performance is not that important. CPU is air cooled by D15S, with single 140mm. RAM is fanless. It means tREFI 32767 etc.

Dear all, let me introduce my 14900KF, the most leaky CPU you've ever seen :cry: Working on 2x 24GB @8000, will post some results soon. I hope it is doable.