Suchergebnisse

I can’t get 2400 FCLK to work. Not even 2300. I get the green screen of death, no matter how much SOC volts I give it. And I don’t think it gets the SOC volts it needs even if it’s clearly set in MPT. I might need the EVC2 after all. 1653357155 FT2 works but you can’t go crazy with the VRAM OC...

Very good. It's not a Butanding1987 method. :)

Seems like it for the 6950 XT, at least. 1653293208 It's the SOC that I'm worried about.

Here you go. For some reason, I get a green screen when I set FCLK to 2300. I have managed with 2200 so far. I'm not sure if I'm getting the SOC volts I WANT because based on HWINFO, the max I got during this Port Royal run was 1.247v. 1653287445 It only pulls the voltage it needs. It idles at...

Not sure if the 6950 XT will benefit from the EVC2 because this card is practically voltage-unlocked. You can give it all the volts it needs through Wattman and it’s a range, not a fixed/constant value like TDVM via MPT. Hmmm… 1653262868 @mantiz How did you make FT2 work? I haven’t touched it...

I got the OCF. Still waiting for the block from China. Ouch. I don’t kniw hiw to overclock an air-cooled card. :D

Nice job. Wouldn't the wires interfere with the thermal pad if you use one with the backplate?

Still no block for the OC Formula.

Why are there no water blocks for the Asrock OC Formula other than Bykski? 1652781199 What could possibly be different in the Extreme Edition given that the Toxic already has a KXTX chip?

@ShirKhan I didn't expect you to be Chinese. @Jacke wie Hose How is your “ass rock”? @Dijati You just need to check if there's a finger cot or thermal pad with unpeeled plastic on your PCB. :d

I didn't know increasing voltage to boost clocks was a novelty, because that's what I've been doing for the past year. But you can only do so much as far as the 6800 XT is concerned (and I reckon any 6000 series cards). Using the EVC2 to increase voltage, I managed to boost my clocks to max...

Does anybody know what's the best alternative thermal pad for the Bykski blocks that use a nonstandard thickness size of 1.2mm? Will a 1.5mm 15w/mk Gelid or Thermalright pad work? thanks

You'd be surprised how much more it can take. My ASIC quality is 86.9%. But my 6800 XT runs better than most 6900 XTs because I can run it at more than 2.8GHz. :D

My 6800 XT vehemently disagrees with you. 1652410818 I think this is only true for Asus motherboards.

:D So stop running Time Spy then. You only need to set your clocks using OverdriveNTool (will Wattman work too?) to check they are where you want them to be. :D

After a crash, my clocks are always >30MHz lower. A cold boot (warm boot doesn’t do it) always solves the problem. @ShirKhan Maybe you should look at your clocks too, not just your FPS. I’m pretty sure the lower frames are due to lower clocks.

@ApolloX I sent you my MPT setting file.

I thought the Conductonaut is only good at minimum 10C?

That looks like a pool. I was very careful not to overdo it on my GPU but I still ended up with too much. After adding a D5 to my loop, the PC refused to boot. I suspected liquid metal must have gotten to the motherboard and was causing a short. I had to disassemble almost everything and I was...

The goal is 25k at 3GHz. :-) But I need winter. :D