SMART Error Log

[cspzagopqy]

Hallo zusammen,

ich habe gerade folgende Meldungen erhalten:

The following warning/error was logged by the smartd daemon:
Device: /dev/nvme0, number of Error Log entries increased from 58 to 59
Device: /dev/nvme1, number of Error Log entries increased from 56 to 57

Ich habe mich noch nie wirklich mit den SMART Werten beschäftigt, aber man sollte diese Fehler doch so sehen können, oder?

root@pve:~# smartctl /dev/nvme0 -x
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.44-2-pve] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Number:                       Samsung SSD 970 EVO Plus 1TB
Serial Number:                      XXX
Firmware Version:                   2B2QEXM7
PCI Vendor/Subsystem ID:            0x144d
IEEE OUI Identifier:                0x002538
Total NVM Capacity:                 1,000,204,886,016 [1.00 TB]
Unallocated NVM Capacity:           0
Controller ID:                      4
Number of Namespaces:               1
Namespace 1 Size/Capacity:          1,000,204,886,016 [1.00 TB]
Namespace 1 Utilization:            727,408,537,600 [727 GB]
Namespace 1 Formatted LBA Size:     512
Namespace 1 IEEE EUI-64:            002538 5c9150726b
Local Time is:                      Fri Jul 10 19:03:19 2020 CEST
Firmware Updates (0x16):            3 Slots, no Reset required
Optional Admin Commands (0x0017):   Security Format Frmw_DL Self_Test
Optional NVM Commands (0x005f):     Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp
Maximum Data Transfer Size:         512 Pages
Warning  Comp. Temp. Threshold:     85 Celsius
Critical Comp. Temp. Threshold:     85 Celsius

Supported Power States
St Op     Max   Active     Idle   RL RT WL WT  Ent_Lat  Ex_Lat
 0 +     7.80W       -        -    0  0  0  0        0       0
 1 +     6.00W       -        -    1  1  1  1        0       0
 2 +     3.40W       -        -    2  2  2  2        0       0
 3 -   0.0700W       -        -    3  3  3  3      210    1200
 4 -   0.0100W       -        -    4  4  4  4     2000    8000

Supported LBA Sizes (NSID 0x1)
Id Fmt  Data  Metadt  Rel_Perf
 0 +     512       0         0

=== START OF SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

SMART/Health Information (NVMe Log 0x02)
Critical Warning:                   0x00
Temperature:                        41 Celsius
Available Spare:                    100%
Available Spare Threshold:          10%
Percentage Used:                    0%
Data Units Read:                    67,429 [34.5 GB]
Data Units Written:                 3,819,227 [1.95 TB]
Host Read Commands:                 1,518,270
Host Write Commands:                150,264,843
Controller Busy Time:               84
Power Cycles:                       41
Power On Hours:                     299
Unsafe Shutdowns:                   10
Media and Data Integrity Errors:    0
Error Information Log Entries:      59
Warning  Comp. Temperature Time:    0
Critical Comp. Temperature Time:    0
Temperature Sensor 1:               41 Celsius
Temperature Sensor 2:               37 Celsius

Error Information (NVMe Log 0x01, max 64 entries)
No Errors Logged

Aber wie ihr seht, seht ihr nix.
Wie kann ich mir diese Error Logs anzeigen lassen?