Recovery inserted = The system starts
1
2
Recovery
from USB stick and allows a BIOS recovery.
Details can be found in the BIOS manual
Fujitsu co-creates with customers to help them digitalize with confidence. We provide innovative IT services and digital technologies including cloud, mobile, AI and security solutions. Together with our stakeholders we contribute to the future of society.
support.ts.fujitsu.com
BIOS Recovery Update
BIOS RecoveryUpdateRecoveryUpdate
► Unzip the ZIP files which were downloaded under Admin package – Compressed Flash Files
and copy the files and directories to the root directory of your USB stick.
► Switch off the system and unplug it from the mains supply.
► Open the casing and enable Recovery using the jumper / DIP switch on the system board.
You will find details on this in the technical manual for the system board.
► Insert the prepared USB stick.
If the Admin package on the prepared USB stick does not match the BIOS
version of the system (e.g. Admin package for BIOS R1.2.0, but BIOS R1.3.0 is
enabled on the system), no screen outputs will be possible in recovery mode. The
Recovery Update will be carried out automatically in this case.
During the Recovery Update, a recurring short signal tone will sound. Recovery of the
system has succeeded if you hear the repeated signal sequence "short-short-long-long"
after a long signal tone. The Recovery process can take a few minutes.
► After the recovery process has finished, switch off the system and
disconnect it from the mains supply.
► Remove the USB stick.
► For all jumpers / DIP switches which were changed, return them to their
original positions and close the casing.
► Connect the system to the mains supply again and switch it on.
The system will now boot up with the new version of BIOS.
► Check the settings in the BIOS Setup. If necessary, configure the settings once again
Fujitsu co-creates with customers to help them digitalize with confidence. We provide innovative IT services and digital technologies including cloud, mobile, AI and security solutions. Together with our stakeholders we contribute to the future of society.
support.ts.fujitsu.com
D3601-A1x - Admin package - Compressed Flash Files
Fujitsu co-creates with customers to help them digitalize with confidence. We provide innovative IT services and digital technologies including cloud, mobile, AI and security solutions. Together with our stakeholders we contribute to the future of society.
support.ts.fujitsu.com
P.S.
Anleitung zum CMOS löschen ohne Jumper
PC stromlos machen: d.h. Netzstecker ziehen. (Bei Notebooks zusätzlich alle Akkus entfernen!)
Den Ein-/Ausschalter vorne am PC-Gehäuse mehrmals betätigen (entleert die Kondensatoren).
Entferne die silberne Knopfzelle (CMOS-Batterie) aus dem Batteriesockel.
Lege eine 10 Euro Cent Münze in den Batteriesockel, zum überbrücken der Plus-/Minuskontakte (siehe Bild, rot/grüne Kreise) des Batteriesockels. (wirkt wie ein Jumper)
Zirka 15 Sekunden warten (je länger desto besser).
Entferne die 10 Euro Cent Münze aus dem Batteriesockel.
Silberne Knopfzelle (CMOS-Batterie) wieder einbauen.
Netzstecker wieder anschliessen. (Bei Notebooks vorher alle Akkus einsetzen)
PC starten, und sofort ins BIOS-Setup gehen um dort die "Setup Defaults/Optimized Settings" zu laden.
Neue BIOS-Einstellungen speichern und Neustart.
Kein Erfolg? Schritt 1-10 mehrmals wiederholen!
Anleitungen zum löschen des CMOS auf PC-Mainboards und Notebooks.
www.biosflash.com
Das macht man da natürlich immer zuerst und entfernt auch den gesetzten Jumper.
