kurze robocopy-Parameter Frage

[michi2k]

Hi, habe gerade ein dämliches Problem.

folgender Robocopy Befehl:

robocopy E:\ G:\robocopy Sicherung /COPY:DAT /E /V /NP /R:1 /W:1 /LOG:F:\RoboLog.txt /TEE

Ich weiss nicht wofür der Parameter /V steht bzw. was er bewirkt.

Blöderweise habe ich bei google nichts über diesen parameter rausbekommen.

EDIT:
So bin doch noch endlich fündig geworden. Wen es interessiert:

produce Verbose output, showing skipped files.

Hier mal der vollständigkeit halber der Rest:

::
:: Copy options :
::
/S :: copy Subdirectories, but not empty ones.
/E :: copy subdirectories, including Empty ones.
/LEV:n :: only copy the top n LEVels of the source directory tree.

/Z :: copy files in restartable mode.
/B :: copy files in Backup mode.
/ZB :: use restartable mode; if access denied use Backup mode.
/EFSRAW :: copy all encrypted files in EFS RAW mode.

/COPY:copyflag :: what to COPY for files (default is /COPYAT).
(copyflags : D=Data, A=Attributes, T=Timestamps).
(S=Security=NTFS ACLs, O=Owner info, U=aUditing info).

/DCOPY:T :: COPY Directory Timestamps.

/SEC :: copy files with SECurity (equivalent to /COPYATS).
/COPYALL :: COPY ALL file info (equivalent to /COPYATSOU).
/NOCOPY :: COPY NO file info (useful with /PURGE).

/SECFIX :: FIX file SECurity on all files, even skipped files.
/TIMFIX :: FIX file TIMes on all files, even skipped files.

/PURGE :: delete dest files/dirs that no longer exist in source.
/MIR :: MIRror a directory tree (equivalent to /E plus /PURGE).

/MOV :: MOVe files (delete from source after copying).
/MOVE :: MOVE files AND dirs (delete from source after copying).

/A+:[RASHCNET] :: add the given Attributes to copied files.
/A-:[RASHCNET] :: remove the given Attributes from copied files.

/CREATE :: CREATE directory tree and zero-length files only.
/FAT :: create destination files using 8.3 FAT file names only.
/256 :: turn off very long path (> 256 characters) support.

/MON:n :: MONitor source; run again when more than n changes seen.
/MOT:m :: MOnitor source; run again in m minutes Time, if changed.

/RH:hhmm-hhmm :: Run Hours - times when new copies may be started.
/PF :: check run hours on a Per File (not per pass) basis.

/IPG:n :: Inter-Packet Gap (ms), to free bandwidth on slow lines.

/SL:: copy symbolic links versus the target.
::
:: File Selection Options :
::
/A :: copy only files with the Archive attribute set.
/M :: copy only files with the Archive attribute and reset it.
/IA:[RASHCNETO] :: Include only files with any of the given Attributes set.
/XA:[RASHCNETO] :: eXclude files with any of the given Attributes set.

/XF file [file]... :: eXclude Files matching given names/paths/wildcards.
/XD dirs [dirs]... :: eXclude Directories matching given names/paths.

/XC :: eXclude Changed files.
/XN :: eXclude Newer files.
/XO :: eXclude Older files.
/XX :: eXclude eXtra files and directories.
/XL :: eXclude Lonely files and directories.
/IS :: Include Same files.
/IT :: Include Tweaked files.

/MAX:n :: MAXimum file size - exclude files bigger than n bytes.
/MIN:n :: MINimum file size - exclude files smaller than n bytes.

/MAXAGE:n :: MAXimum file AGE - exclude files older than n days/date.
/MINAGE:n :: MINimum file AGE - exclude files newer than n days/date.
/MAXLAD:n :: MAXimum Last Access Date - exclude files unused since n.
/MINLAD:n :: MINimum Last Access Date - exclude files used since n.
(If n < 1900 then n = n days, else n = YYYYMMDD date).

/XJ :: eXclude Junction points. (normally included by default).

/FFT :: assume FAT File Times (2-second granularity).
/DST :: compensate for one-hour DST time differences.

/XJD :: eXclude Junction points for Directories.
/XJF :: eXclude Junction points for Files.

::
:: Retry Options :
::
/R:n :: number of Retries on failed copies: default 1 million.
/W:n :: Wait time between retries: default is 30 seconds.

/REG :: Save /R:n and /W:n in the Registry as default settings.

/TBD :: wait for sharenames To Be Defined (retry error 67).

::
:: Logging Options :
::
/L :: List only - don't copy, timestamp or delete any files.
/X :: report all eXtra files, not just those selected.
/V :: produce Verbose output, showing skipped files.
/TS :: include source file Time Stamps in the output.
/FP :: include Full Pathname of files in the output.
/BYTES :: Print sizes as bytes.

/NS :: No Size - don't log file sizes.
/NC :: No Class - don't log file classes.
/NFL :: No File List - don't log file names.
/NDL :: No Directory List - don't log directory names.

/NP :: No Progress - don't display % copied.
/ETA :: show Estimated Time of Arrival of copied files.

/LOG:file :: output status to LOG file (overwrite existing log).
/LOG+:file :: output status to LOG file (append to existing log).

/UNILOG:file :: output status to LOG file as UNICODE (overwrite existing log).
/UNILOG+:file :: output status to LOG file as UNICODE (append to existing log).

/TEE :: output to console window, as well as the log file.

/NJH :: No Job Header.
/NJS :: No Job Summary.

/UNICODE :: output status as UNICODE.

::
:: Job Options :
::
/JOB:jobname :: take parameters from the named JOB file.
/SAVE:jobname :: SAVE parameters to the named job file
/QUIT :: QUIT after processing command line (to view parameters).
/NOSD :: NO Source Directory is specified.
/NODD :: NO Destination Directory is specified.
/IF :: Include the following Files.

 

[Patric_]

Falls noch jemand interessiert:

robocopy /? zeigt alle Parameter an

Und noch "wichtiger":
Wenn von NTFS auf FAT (oder irgendein anderes Dateisystem gesichert wird, ich sichere z.B. auf ein Buffalo NAS (also irgendein "Linux-Dateiystem" ) ist der Schalter /FFT :: assume FAT File Times (2-second granularity). äußerst nützlich, sonst unterscheiden sich nachm Kopieren die Daten oft um +-1 Sekunde und robocopy kopiert immer und immer wieder die gleichen Dateien, obwohl sich nix geändert hat