Mac g5 bench

[arg-ist]

G5 BENCH

As ı said before there are 2 new MAC G5 mods on the table.My first worklog MAC G5 ATX (passive watercooled) is finished. I take final photos.I t is time to begin with a new worklog.

1-My first worklog was MAC ATX (passive watercooled)

Link MAC G5 ATX Passive watercooled.
http://www.hardwareluxx.de/community/f143/mac-g5-mod-arg-ist-1050219.html

2. This time again a MAC G5 , but as a BENCH CASE.

3-And my next worklog again a MAC G5 … But this time as a JUMBO MAC G5 = MAC G5 STACKER

MAC G5 STACKER

I want to make a TRILOGY with MAC G5 cases.


This time ı want to make a different BENCH CASE from this case.
A combination of aluminum and acrylic.

I will use this case

R1

But ı wll use only back side panel and the four handles of the case

R 2

Case tilted

R 3

As a bench case there are two ways that we can use.


1-Handles at front and back panels

R4

2-Handles at sides
I shall use it , this way.

R 5

I want to install 2x360 rads in to the bulge of handles. And PSU ,POMP ,HDD etc . in this case

R 6

As usally, MB on the top, on a thick plexi, as MB TRAY .that can be opened to back.
As ı used it at my first BENCH Worklog

And ı wannt to mount the video card with a 16X riser card extender flex. To prevent the height of the case ,becouse ı wannt to make a flap cover from plexi.(If ı can do it…)

R6a

 

[arg-ist]

First a recess for rads and rad grils in to the handles , from acrylic. Drawn at corel
R 7

And laser cut from 5 mm acrylic
R 8

To bend the acrylics, ı made a mold from MDF.
R 9

I can bend acrylic using this mold
R 10

Acrylic plate on the mold
R 11

Acrylic plate fixed to the mold
R 12

Heating of acrylic with heat gun.
R 13

And bending of softened acrylic
R 14

Bended acrylics
R 15- 16

Bended acrylic mounted to the case for trial purposes.
R 17-18-19

And second side panel bended likewise.
R 20

Two side panels are ready
R 21

Second side panel mounted too… for trial purposes
R 22-23

 

[arg-ist]

Four Silverstone case feets mounted to the bottom of the case
R25

Next stage is front and back panel
Made from 3mm thick acrylic a pattern for front and back panel. And mounted to control.
Resim24

At front panel ı don t wannt to use a lott of displays. I want to use 2x lcd temp. displays for radiator entries and 2x lcd temp. Display for rad outputs.total 4 LCD displays for temp. And a fan controllerfor fans.

And some researches for their placement

R26-27-28-29

I have tried with different reservoirs EK X3, Bitspower. With 60 mm Radius.
but I do not like any

the most appropriate was EK Tube res X3 60 mm
R38

but want to keep the cables of PSU.
Masking could be a solution to it..

R 39 40 41

I wanted a different solution
At last ı decided to use a wider resorvoir 150mm Radius , to make reservoir as essential element.

I must make a Jumbo reservoir from acrylic tube like this
R30

And use reservoir as essential element. of the buttom case like this
R 31 32 33
Reservoir with extrem 150mm Radius. Was to big for this case.

Therefore ı decided to make it with 120 mm Radius
R 34 35 36 37

It is time to make a custom Tube reservoir with 120 mm Radius.