Rack-Case Empfehlungen gesucht

ipmi-sensors-config -h 192.168.178.12 -l admin -u ADMIN -p [DeinPW] -L
ipmi-sensors-config -h 192.168.178.12 -l admin -u ADMIN -p [DeinPW] -o -S 674_FAN2
ipmi-sensors-config -h 192.168.178.12 -l admin -u ADMIN -p [DeinPW] -c -e 607_FAN1:Lower_Critical_Threshol=300.000000

Erstes Kommando zeigt quasi Geräte, die Du ansprechen kannst. Insbesondere also auch für die Lüfter, bei mir z.B.:
607_FAN1
674_FAN2
808_FAN4
875_FANA

Das Zweite Kommando gibt dir die aktuellen Settings des angegebenen Geräts.

Das dritte Kommando setzt den Schwellenwert für lower-critical auf 300 bei FAN1. Lower-critical ist wenn ich mich richtig erinnere und nach meiner bescheidenen Erfahrung der spannende, weil der eben für Panik und Hochdrehen aller Lüfter steht. Ist glaub von Haus aus auf 500 gesetzt.

EDIT: Typo im Kommando impi—>ipmi korrigiert.
 
Zuletzt bearbeitet:
Wenn Du diese Anzeige nicht sehen willst, registriere Dich und/oder logge Dich ein.
besterino schrieb:
ipmi-sensors-config -h 192.168.178.12 -l admin -u ADMIN -p [DeinPW] -L
ipmi-sensors-config -h 192.168.178.12 -l admin -u ADMIN -p [DeinPW] -o -S 674_FAN2
ipmi-sensors-config -h 192.168.178.12 -l admin -u ADMIN -p [DeinPW] -c -e 607_FAN1:Lower_Critical_Threshol=300.000000

Erstes Kommando zeigt quasi Geräte, die Du ansprechen kannst. Insbesondere also auch für die Lüfter, bei mir z.B.:
607_FAN1
674_FAN2
808_FAN4
875_FANA

Das Zweite Kommando gibt dir die aktuellen Settings des angegebenen Geräts.

Das dritte Kommando setzt den Schwellenwert für lower-critical auf 300 bei FAN1. Lower-critical ist wenn ich mich richtig erinnere und nach meiner bescheidenen Erfahrung der spannende, weil der eben für Panik und Hochdrehen aller Lüfter steht. Ist glaub von Haus aus auf 500 gesetzt.

EDIT: Typo im Kommando impi—>ipmi korrigiert.
Zum Vergrößern anklicken....

Merci. Probiere ich die Tage.
 
Fehler tritt immernoch auf, obwohl die Kommandos fehlerfrei durchgelaufen sind. Lower Critical Thresholds sind auf 300 rpm gesetzt
 
Zuletzt bearbeitet:
Was zeigen Dir denn die Sensoren min webclient? Mal auf autoupdate setzen, bisserl beobachten und schauen, ob da irgendwo was als „critical“ angezeigt wird, bevor da alle hochdrehen.
 
besterino schrieb:
Was zeigen Dir denn die Sensoren min webclient? Mal auf autoupdate setzen, bisserl beobachten und schauen, ob da irgendwo was als „critical“ angezeigt wird, bevor da alle hochdrehen.
Zum Vergrößern anklicken....

Servus,

war leider viel los die letzte Zeit.

Nachdem ich deine Kommandos ausgeführt habe, drehen die Lüfter Konstant. Meine Kommandos sahen so aus:

Code: 
ipmi-sensors-config -h 10.24.107.69 -l admin -u ADMIN -p XXX -c -e 607_FAN1:Lower_Critical_Threshold=300.000000
ipmi-sensors-config -h 10.24.107.69 -l admin -u ADMIN -p XXX -c -e 674_FAN2:Lower_Critical_Threshold=300.000000
ipmi-sensors-config -h 10.24.107.69 -l admin -u ADMIN -p XXX -c -e 808_FAN3:Lower_Critical_Threshold=300.000000
ipmi-sensors-config -h 10.24.107.69 -l admin -u ADMIN -p XXX -c -e 875_FANA:Lower_Critical_Threshold=300.000000

Aktuell sieht die Übersicht so aus:

FAN1:

Code: 
Section 607_FAN1
        ## Possible values: Yes/No
        Enable_All_Event_Messages                                                   Yes
        ## Possible values: Yes/No
        Enable_Scanning_On_This_Sensor                                              Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Critical_Going_Low                             Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Non_Recoverable_Going_Low                      Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Critical_Going_High                            Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Non_Recoverable_Going_High                     Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Critical_Going_Low                           Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Non_Recoverable_Going_Low                    Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Critical_Going_High                          Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Non_Recoverable_Going_High                   Yes
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Critical_Threshold                                                300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Recoverable_Threshold                                             300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Critical_Threshold                                                1000.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Critical_Threshold                                                    25400.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Recoverable_Threshold                                             25500.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Positive_Going_Threshold_Hysteresis                                         100.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Negative_Going_Threshold_Hysteresis                                         100.000000
EndSection


FAN2
Code: 
Section 674_FAN2
        ## Possible values: Yes/No
        Enable_All_Event_Messages                                                   Yes
        ## Possible values: Yes/No
        Enable_Scanning_On_This_Sensor                                              Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Critical_Going_Low                             Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Non_Recoverable_Going_Low                      Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Critical_Going_High                            Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Non_Recoverable_Going_High                     Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Critical_Going_Low                           Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Non_Recoverable_Going_Low                    Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Critical_Going_High                          Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Non_Recoverable_Going_High                   Yes
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Critical_Threshold                                                300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Recoverable_Threshold                                             300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Critical_Threshold                                                1000.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Critical_Threshold                                                    25400.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Recoverable_Threshold                                             25500.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Positive_Going_Threshold_Hysteresis                                         100.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Negative_Going_Threshold_Hysteresis                                         100.000000
EndSection


FAN3:

Code: 
Section 741_FAN3
        ## Possible values: Yes/No
        Enable_All_Event_Messages                                                   Yes
        ## Possible values: Yes/No
        Enable_Scanning_On_This_Sensor                                              Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Critical_Going_Low                             Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Non_Recoverable_Going_Low                      Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Critical_Going_High                            Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Non_Recoverable_Going_High                     Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Critical_Going_Low                           Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Non_Recoverable_Going_Low                    Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Critical_Going_High                          Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Non_Recoverable_Going_High                   Yes
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Critical_Threshold                                                300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Recoverable_Threshold                                             300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Critical_Threshold                                                1000.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Critical_Threshold                                                    25400.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Recoverable_Threshold                                             25500.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Positive_Going_Threshold_Hysteresis                                         100.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Negative_Going_Threshold_Hysteresis                                         100.000000
EndSection

FAN4 ist nicht angeschlossen.

FANA

Code: 
Section 875_FANA
        ## Possible values: Yes/No
        Enable_All_Event_Messages                                                   Yes
        ## Possible values: Yes/No
        Enable_Scanning_On_This_Sensor                                              Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Critical_Going_Low                             Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Non_Recoverable_Going_Low                      Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Critical_Going_High                            Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Non_Recoverable_Going_High                     Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Critical_Going_Low                           Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Non_Recoverable_Going_Low                    Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Critical_Going_High                          Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Non_Recoverable_Going_High                   Yes
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Critical_Threshold                                                300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Recoverable_Threshold                                             300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Critical_Threshold                                                1000.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Critical_Threshold                                                    25400.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Recoverable_Threshold                                             25500.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Positive_Going_Threshold_Hysteresis                                         100.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Negative_Going_Threshold_Hysteresis                                         100.000000
EndSection

Nen Screenshot vom IPMI habe ich auch noch zu bieten.
IPMI.PNG
 
Hab noch nicht im Detail gelesen, aber ein Tipp auf die Schnelle: Ich meine, ich musste danach rebooten, damit die neuen Werte effektiv wurden.

Und den non-recoverable ggf. noch weiter runter setzen (200 oder so?).
 
Zuletzt bearbeitet:
besterino schrieb:
Hab noch nicht im Detail gelesen, aber ein Tipp auf die Schnelle: Ich meine, ich musste danach rebooten, damit die neuen Werte effektiv wurden.

Und den non-recoverable ggf. noch weiter runter setzen (200 oder so?).
Zum Vergrößern anklicken....

Aktuell sehen die Werte so aus:

FAN1:

Code: 
Section 607_FAN1
        ## Possible values: Yes/No
        Enable_All_Event_Messages                                                   Yes
        ## Possible values: Yes/No
        Enable_Scanning_On_This_Sensor                                              Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Critical_Going_Low                             Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Non_Recoverable_Going_Low                      Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Critical_Going_High                            Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Non_Recoverable_Going_High                     Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Critical_Going_Low                           Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Non_Recoverable_Going_Low                    Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Critical_Going_High                          Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Non_Recoverable_Going_High                   Yes
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Critical_Threshold                                                300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Recoverable_Threshold                                             200.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Critical_Threshold                                                1000.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Recoverable_Threshold                                             300.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Positive_Going_Threshold_Hysteresis                                         100.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Negative_Going_Threshold_Hysteresis                                         100.000000
EndSection

Code: 
FAN2:

Section 674_FAN2
        ## Possible values: Yes/No
        Enable_All_Event_Messages                                                   Yes
        ## Possible values: Yes/No
        Enable_Scanning_On_This_Sensor                                              Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Critical_Going_Low                             Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Non_Recoverable_Going_Low                      Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Critical_Going_High                            Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Non_Recoverable_Going_High                     Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Critical_Going_Low                           Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Non_Recoverable_Going_Low                    Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Critical_Going_High                          Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Non_Recoverable_Going_High                   Yes
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Critical_Threshold                                                300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Recoverable_Threshold                                             200.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Critical_Threshold                                                1000.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Recoverable_Threshold                                             300.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Positive_Going_Threshold_Hysteresis                                         100.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Negative_Going_Threshold_Hysteresis                                         100.000000
EndSection


FAN3

Code: 
Section 741_FAN3
        ## Possible values: Yes/No
        Enable_All_Event_Messages                                                   Yes
        ## Possible values: Yes/No
        Enable_Scanning_On_This_Sensor                                              Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Critical_Going_Low                             Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Non_Recoverable_Going_Low                      Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Critical_Going_High                            Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Non_Recoverable_Going_High                     Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Critical_Going_Low                           Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Non_Recoverable_Going_Low                    Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Critical_Going_High                          Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Non_Recoverable_Going_High                   Yes
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Critical_Threshold                                                300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Recoverable_Threshold                                             200.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Critical_Threshold                                                1000.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Recoverable_Threshold                                             300.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Positive_Going_Threshold_Hysteresis                                         100.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Negative_Going_Threshold_Hysteresis                                         100.000000
EndSection

FANA:

Code: 
Section 875_FANA
        ## Possible values: Yes/No
        Enable_All_Event_Messages                                                   Yes
        ## Possible values: Yes/No
        Enable_Scanning_On_This_Sensor                                              Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Critical_Going_Low                             Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Lower_Non_Recoverable_Going_Low                      Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Critical_Going_High                            Yes
        ## Possible values: Yes/No
        Enable_Assertion_Event_Upper_Non_Recoverable_Going_High                     Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Critical_Going_Low                           Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Lower_Non_Recoverable_Going_Low                    Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Critical_Going_High                          Yes
        ## Possible values: Yes/No
        Enable_Deassertion_Event_Upper_Non_Recoverable_Going_High                   Yes
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Critical_Threshold                                                300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Lower_Non_Recoverable_Threshold                                             200.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Critical_Threshold                                                1000.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Critical_Threshold                                                    300.000000
        ## Give valid input for sensor type = Fan; units = RPM
        Upper_Non_Recoverable_Threshold                                             300.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Positive_Going_Threshold_Hysteresis                                         100.000000
        ## Give valid input for sensor type = Fan; units = RPM; 'None' to not use hysteresis
        Negative_Going_Threshold_Hysteresis                                         100.000000
EndSection


ipmitool

Code: 
[root@tesla ~]# ipmitool sensor | grep -E "^FAN|^CPU Temp"                                                                          
CPU Temp         | 26.000     | degrees C  | ok    | 0.000     | 0.000     | 0.000     | 95.000    | 100.000   | 100.000            
FAN1             | 1400.000   | RPM        | nr    | 200.000   | 300.000   | 300.000   | 1000.000  | 300.000   | 300.000            
FAN2             | 3200.000   | RPM        | nr    | 200.000   | 300.000   | 300.000   | 1000.000  | 300.000   | 300.000            
FAN3             | 1500.000   | RPM        | nr    | 200.000   | 300.000   | 300.000   | 1000.000  | 300.000   | 300.000            
FAN4             | na         |            | na    | na        | na        | na        | na        | na        | na                 
FANA             | 1100.000   | RPM        | nr    | 200.000   | 300.000   | 300.000   | 1000.000  | 300.000   | 300.000

Bild:


IPMI_2.PNG

Vielen Dank schon mal im Vorraus.
 
Anmelden, um zu antworten.

Ähnliche Themen

S
Kaufberatung 19" Server/Storage Case
Antworten
17
Aufrufe
834
pwnbert
pwnbert
C
[Kaufberatung] Full HD Build in kleinerem Case für ins Regal gesucht
Antworten
18
Aufrufe
789
ChckNrrs
C
Hardwareluxx setzt keine externen Werbe- und Tracking-Cookies ein. Auf unserer Webseite finden Sie nur noch Cookies nach berechtigtem Interesse (Art. 6 Abs. 1 Satz 1 lit. f DSGVO) oder eigene funktionelle Cookies. Durch die Nutzung unserer Webseite erklären Sie sich damit einverstanden, dass wir diese Cookies setzen. Mehr Informationen und Möglichkeiten zur Einstellung unserer Cookies finden Sie in unserer Datenschutzerklärung.


Zurück
Oben Unten refresh