Abit AN7

nOti

Semiprofi
Thread Starter
Mitglied seit
27.05.2003
Beiträge
1.125
Ort
Neuruppin
hallo leute ich habe ein komplett pc hiermal die daten... ;)

und nu wollte ich fragen ob sich das sohnt das Abit AN7 zu holen

habe ne Radeon 9800 XT & 1 GB DDR400 PC3200 DualChannel Speicher

Abit AN7
---------
NVIDIA nForce2 Based AMD K7 Mainboard
FSB400, Dual DDR400, SATA RAID, IEEE1394
ABIT μGuru Technologie
---------


SiSoftware Sandra

System
Manufacturer : HPPAV
Model : MS-7027
ID : 95144690-11B21E58-45640080-73694E6E

Mainboard
Manufacturer : MICRO-STAR INTERNATIONAL CO., LTD
MP Support : 1 CPU(s)
MPS Version : 1.40
Model : MS-7027

System Memory Controller
Location : Mainboard
Error Correction Capability : None
Number of Memory Slots : 3
Maximum Installable Memory : 3GB
Bank0/1 - A0 : None None None None DIMM 512MB
Bank2/3 - A1 : None None None None DIMM 512MB
Bank4/5 - A2 : Empty

Chipset 1
Model : VIA Technologies Inc VT8377 Apollo KT400/A/600 CPU to PCI Bridge
Bus(es) : ISA AGP PCI IMB USB FireWire/1394 i2c/SMBus
Front Side Bus Speed : 2x 199MHz (398MHz data rate)
Maximum FSB Speed / Max Memory Speed : 2x 200MHz / 2x 200MHz
Width : 64-bit
IO Queue Depth : 4 request(s)

Chipset 1 Hub Interface
Type : V-Link
Width : 8-bit
Full Duplex : Yes
Multiplier : 1/1x
Speed : 8x 66MHz (528MHz data rate)
IO Queue Depth : 9 request(s)

Logical/Chipset 1 Memory Banks
Bank 0 : 256MB DDR-SDRAM 2.5-3-3-7CL 2CMD
Bank 1 : 256MB DDR-SDRAM 2.5-3-3-7CL 2CMD
Bank 2 : 256MB DDR-SDRAM 2.5-3-3-7CL 2CMD
Bank 3 : 256MB DDR-SDRAM 2.5-3-3-7CL 2CMD
Bank Interleave : 4-way
Speed : 2x 199MHz (398MHz data rate)
Multiplier : 1/1x
Width : 64-bit
Power Save Mode : No
Fixed Hole Present : No

APIC 1
Version : 0.03
Speed : 16MHz
Multiplier : 1/2x
Maximum Interrupts : 24
IRQ Handler Engaged : Yes
Enhanced Support : Yes

Memory Module(s)
Memory Module 1 : Y380032JD-32510-93022602 51046732119 512MB 16x(32Mx8) DDR-SDRAM PC3200U-2544-600 (CL2.5 up to 200MHz)
Memory Module 2 : Y380032JD-32510-93022602 51046732119 512MB 16x(32Mx8) DDR-SDRAM PC3200U-2544-600 (CL2.5 up to 200MHz)

Environment Monitor 1
Model : Winbond W83697HF ISA
Version : 6.00
Mainboard Specific Support : No

Temperature Sensor(s)
Board Temperature : 24.0°C / 75.2°F
CPU Temperature : 47.5°C / 117.5°F

Cooling Device(s)
Auto Fan Speed Control : No
CPU Fan Speed : 4116rpm

Voltage Sensor(s)
CPU Voltage : 1.63V
+3.3V Voltage : 3.36V
+5V Voltage : 5.08V
+12V Voltage : 12.34V
-12V Voltage : -12.36V
-5V Voltage : -5.20V
Standby Voltage : 5.02V
Battery Voltage : 3.66V

AGP Bus(es) on Hub 1
Version : 3.05
Speed : 8x 66MHz (528MHz data rate)
Multiplier : 1/2x
Fast-Writes Enabled : No
Isochronous Mode Enabled : No
Addressing Enabled : 32-bit
Aperture Size : 256MB

PCI Bus(es) on Hub 1
Version : 2.10
Number of Bridges : 1
PCI Bus 0 : PCI (33MHz)
Multiplier : 1/6x

LPC Hub Controller 1
Model : VIA Technologies Inc VT8237 PCI to ISA Bridge
ACPI Power Management Enabled : Yes
Multiplier : 1/4x
Speed : 8MHz
DMA Multiplier : 1/2x
DMA Speed : 4MHz

USB Controller 1
Model : VIA Technologies Inc VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 2
Model : VIA Technologies Inc VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 3
Model : VIA Technologies Inc VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 4
Model : VIA Technologies Inc VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)
Version : 1.10
Interface : UHCI
Channels : 2
Speed : 48MHz
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps)
Legacy Emulation Enabled : No

USB Controller 5
Model : VIA Technologies Inc VT6202 USB 2.0 Enhanced Host Controller
Version : 2.00
Specification : 1.00
Interface : EHCI
Channels : 8
Companion Controllers : 4
Supported Speed(s) : Low (1.5Mbps) Full (12Mbps) High (480Mbps)
Addressing Support : 32-bit
Legacy Emulation Enabled : No

FireWire/1394 Controller 1
Model : Creative Labs Audigy 2 Firewire Controller
Version : 1.10
Interface : OHCI
Enhanced Support : No
Channels : 64
Speed : 400MHz

FireWire/1394 Controller 2
Model : Micro-Star International Co Ltd (MSI) VT6306 VIA Fire II IEEE-1394 OHCI Link Layer Controller
Version : 1.00
Interface : OHCI
Enhanced Support : No
Channels : 64
Speed : 400MHz

System SMBus Controller 1
Model : VIA VT823x SMBus
Advanced TCO Mode Enabled : No
Slave Device Enabled : No
PEC Support : No
Speed : 16kHz

Expansion Slot(s)
PCI0 (1h) : PCI 32-bit +5V PME Full-Length Available (VIA Technologies Inc ProSavageDDR P4X600 CPU to AGP Bridge)
PCI1 (2h) : PCI 32-bit +5V PME Full-Length Available
PCI2 (3h) : PCI 32-bit +5V PME Full-Length Used
PCI3 (4h) : PCI 32-bit +5V PME Full-Length Available
AGP (8h) : AGP 32-bit +5V Full-Length Available (ATI Technologies Radeon 9800 XT (R350))

Port Connector
PRIMARY IDE : None - ATA / None
SECONDARY IDE : None - ATA / None
FDD : 8251 FIFO - Floppy Disk / None
COM1 : Serial Port 16450 - 9 Pin Dual Inline / DB-9 pin male
COM2 : Serial Port 16450 - 9 Pin Dual Inline / DB-9 pin male
LPT1 : Parallel Port ECP/EPP - DB-25 pin female / DB-25 pin female
Keyboard : Keyboard - PS/2 / PS/2
PS/2 Mouse : Mouse - PS/2 / PS/2
USB0 : USB - None / None
AUDIO : Audio - None / None

Performance Tips
Notice 224 : SMBIOS/DMI information may be inaccurate.
Tip 2511 : Some memory slots are free so the memory can be easily upgraded.
Warning 2545 : Large memory modules should be Registered/Buffered.
Tip 2546 : Large memory modules should be ECC/Parity.
Tip 2 : Double-click tip or press Enter while a tip is selected for more information about the tip.
 
Wenn Du diese Anzeige nicht sehen willst, registriere Dich und/oder logge Dich ein.
Was für einen Chipsatz hat das Board dann genau ??? Den oben geposteten Informationen zur Folge isses entweder ein KT400A oder ein KT600. Meiner Meinung nach lohnt sich das nicht wirklich, es sei den du achtest auf jedes einzelne Frame. Aber einen großen Performance Schub wirste nicht merken !!!
 
ich denke auch kaum dasde da viel merken wirst, bisschen was eben durhc dualchannel etc.
dafür machen die nvidia treiber mehr stress und das an7, vorallem in der allerneuesten revision, wird schweineheiss.. da glühen die mosfets selbst bei passiv mosfetkühlung noch bei knappen 60°
 
also mir hat man gesagt das sich das sehr lohn... da ich auch nen komplett pc von hp habe...

MS-7027 dafür findet man auch keine treiber nix.... das is ja das prob...
 
Kommt auch drauf an ob du mit dem neuen board evtl oc'en willst, bzw was du für eine CPU+Kühlung besitzt!?
 
nOti schrieb:
also mir hat man gesagt das sich das sehr lohn... da ich auch nen komplett pc von hp habe...

MS-7027 dafür findet man auch keine treiber nix.... das is ja das prob...

treiber - www.viaarena.com :rolleyes:
bios - schwer.


Hmm, aber wenn du OC'en willst dan lohnt es sich schon nen neues bord zu kaufen.

Aber dann wirst du auch warscheinlich einpaar schwirigkeiten bekommen - OEM PC's haben meist Micro-ATX cases, also das heisst da is nix mit AN7.
 
Hardwareluxx setzt keine externen Werbe- und Tracking-Cookies ein. Auf unserer Webseite finden Sie nur noch Cookies nach berechtigtem Interesse (Art. 6 Abs. 1 Satz 1 lit. f DSGVO) oder eigene funktionelle Cookies. Durch die Nutzung unserer Webseite erklären Sie sich damit einverstanden, dass wir diese Cookies setzen. Mehr Informationen und Möglichkeiten zur Einstellung unserer Cookies finden Sie in unserer Datenschutzerklärung.


Zurück
Oben Unten refresh