Hallo habe das hier gestern gelesen und heute meine neue CPU Q9550 verbaut und siehe da die MCH lässt sich in der Range 1.20V - 1.40V nicht verstellen, ich habe mit Auto immer 1.40V
Das mußt du mir erklären. Du stellst die MCH auf Auto und hast dann 1,4V anliegen? Mit was gemessen (ET6)?
Kannst du mir einen Gefallen tun? Alles wie in dem Template einstellen (einfach LOAD OPTIMIZED DEFAULTS) ,dann eben die paar Details und noch deine Speicherspannung.
Und dann mal bitte testen, ob du mit einer MCH über 1,2V (meinetwegen auch gleich 1,4V noch booten kannst)
BIOS Setting
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio .......................: 8,0
Fine CPU Clock Ratio...................: +0.5
CPU Frequency .........................: 2.83GHz (333X8)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [DISABLED]
CPU Host Frequency (Mhz) ..............: 333
PCI Express Frequency (Mhz) ...........: 100
C.I.A.2 ...............................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive........................: 800mV
PCI Express Clock Drive................: 900mV
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)....................: 0ps
DRAM Performance Control
Performance Enhance....................: [STANDARD]
Extreme Memory Profile (X.M.P.)........: [Disabled]
(G)MCH Frequency Latch.................: [AUTO]
System Memory Multiplier ..............: [AUTO]
Memory Frequency (Mhz) ................: 1066
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time.......................: 5
tRCD ..................................: 5
tRP'...................................: 5
tRAS...................................: 15
Advanced Timing Control -> alles auf Auto
Channel A
Static tRead Value.....................: 10
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO]
Twr2wr(Different Rank).................: 8 [AUTO]
Twr2rd(Different Rank).................: 7 [AUTO]
Trd2wr(Same/Diff Rank).................: 9 [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]
Channel B
Static tRead Value.....................: 10
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO]
Twr2wr(Different Rank).................: 8 [AUTO]
Twr2rd(Different Rank).................: 7 [AUTO]
Trd2wr(Same/Diff Rank).................: 9 [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]
Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Disabled]
CPU Vcore...................1.250v : Auto
CPU Termination...........1.200v: Auto
CPU PLL.......................1.500v: Auto
CPU Reference.............0.760v: [Auto]
MCH/ICH
MCH Core.....................1.100v: 1,2->Boot, keine Probs, 1,3-> endlos Reboot
MCH Reference............0.760v.: [AUTO]
MCH/DRAM Ref..........0.900v.: [AUTO]
ICH I/O........................1.500v: [AUTO]
ICH Core......................1.100v: [AUTO]
DRAM
DRAM Voltage...................1.800v.: 2.14v
DRAM Termination ......................: 0.900V [AUTO]
Channel A Reference....................: 0.900V [AUTO]
Channel B Reference ...................: 0.900V [AUTO]
Advanced Settings
Limit CPUID Max. to 3..................: [Disabled]
No-Execute Memory Protect..............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support...................: [Disabled]
x C4/C4E State Support.................: [Disabled]
CPU Thermal Monitor 2(TM2) ............: [Enabled]
CPU EIST Function......................: [Disabled]
Virtualization Technology..............: [Enabled]
Stell doch mal bitte alles auf DEFAULT