Suchergebnisse

Hi, did you ever test my settings to see if they will let you run 1.128v load successfully as looping? (Core PLL 0.975v. VCCIN: 1.86-1.87v).

Yes it will still help. The bend isn't permanent (most of the bend will become straight when the pressure is released). Even if it still isn't perfect, the thermalright bracket will still improve things greatly. When I got my RPL QS chip from Asus, I didn't even install it with the intel ILM...

Your P-Core SP is the same as mine (mine is 113 P core SP, 94 E core SP, so 106 SP total). You should be able to pass 1.128v load by doing the following settings. (1.220v BIOS set, LLC=6): 1. CPU VCCIN: 1.860v <--helps with PCIE Bus WHEA errors, it seems increasing VCCIN may take some...

It's just socket sense. You only get die sense on the Maximus boards. I think you can use "OCTool" and go to "Raw VRM", or you can use Asus EC In hwinfo64 and look for IOUT or "CPU Current". then you can use simple math to get your vcore. BIOS Vcore set - (IOUT * Loadline mohms) = VR VOUT...

1.29v set in BIOS + LLC6 on a Strix? 1.27v load reported is about 1.19v die sense, because if I set 1.27v load on Maximus Extreme LLC6, I get 1.172v in R23. But Strix doesn't have die sense, it has Socket Sense (Super I/O) so Vcore at LLC6 will "Look" flat, but it's actually 0.49 mOhms of...

What's the P core SP on your chip? I searched your posts but I can't find anything. Maybe because i have to translate into english :(

Probably windows 10. I installed the w11 22h2 ISO and had no problems. Also, W11 22H2 fixed the problem I had with previous builds of Windows 11,with the P cores going completely to sleep and all the E cores loaded when I ran Stockfish Chess and then opened or alt tabbed to a web browser, which...

113 is above average already on P cores. 70% of retail chips are below SP 100 total, which is usually about <106 P core SP.

I talked to Shamino. All of the P core 138 and 140 values are not correct. This seems to be a bug. Sometimes this can be caused by low battery (cmos) but I need to ask: 1. Are all of you with this pcore, upgrading from ADL CPU previously in the socket? 2. Are you guys using the same bios...

Please update the Intel Management Engine Firmware or you will have Qcode and M.2 drive problems!

Keep in mind that the total SP is influenced by both P and E cores. A giant P core and low E core will drag the total SP down a bit. I haven't seen what's behind a lower E core (.eg under 80) has on E core clocks. But people with P cores greater than 100 should test their vmins (min voltage at...

Test it at 5.7 ghz as I mentioned earlier. If it passes SP is true. Start at 1.250v bios set + LLC6 Run R23 for 15 minutes check HWinfo64 for WHEA errors. If fail, raise vcore by 10, if pass, lower vcore by 10. Post final (last) stable results.

Yes, everything enabled (Disable C-states so vmin can be easily seen in hwinfo64). Either post VR VOUT if HWinfo supports it, Die sense vcore (Asus), or "Bios Set Vcore + LLC" (other boards) because Load LLC Vcore can be easily calculated with amps and mohms, if LLC6/Mode 3/Turbo = 0.49 moms...

sorry i don't, it's buried in the forum thread.

For you guys with golden binned SP samples, can you try to manually set your vcore, to avoid 100C, and try to pass Cinebench R23 at 5.7 ghz sync all P cores, please? Start at 1.250v Bios set, llc=level 6 (Asus), Mode 3 (MSI), Turbo (Gigabyte), note: use fixed mode on GB, not "override mode", and...

you need the newer version. 14 not 13. One was posted on the ddr5 thread on overclock.net a few days ago. old versions will not work.

Stockfish is the gold standard for testing true stability. Use the AVX2 or BMI2 instruction (Haswell) versions. https://abrok.eu/stockfish/ If you don't have chessbase, you can use Arena UCI engine to install stockfish, but you have to make sure you set the # of CPU cores (=threads) and also...

AC Loadline functions differently on Z490 and newer than it did on Z390 and older. First, ACLL affects CPU VID. On manual vcore, CPU VID is ignored because you are setting vcore manually. On Auto vcore, or "adaptive mode", ACLL will be used. (and other parameters, like voltage +/- offset, or...

Did doing a "Half turn" of the torx screws on an Apex (or Extreme or Hero), instead of actual washers, help those boards any?

Did you change PLL Termination Voltage?