Suchergebnisse

testing 1102 bios in encore and seens very gud.. vei i have an question to you Lets hypothetically say i dont need speed at all.. 6000mt/s and 4.5ghz cpu clock speed will be same as 8000/5.4 which is kinda the case i am right now, I play games that are from 1998.. or even hypothetically another...

Setup Question = Memory Test on Warm Boot Help String = Enable Or Disable Base Memory Test Run on Warm Boot Token =642 // Do NOT change this line Offset =1A3 Width =01 BIOS Default =[01]Enabled Options =[00]Disabled // Move "*" to the desired Option *[01]Enabled Here is the full...

vei what about those scewin variables MRC ULT Safe Config Force ColdReset Training Profile MCH Full Check Safe Mode Support Memory Test on Warm Boot maybe any benefit with tradeoff of booting time?

off mc sp 76, not so bad for 14700kf spyed an FF3D532G8000HC38DDC01 teamgroup 2x16 8000 and what i got was class V :/ maybe i buy a bunch of green sticks again from aliexpress

I struggled(what a surprise) on 8000 in delta method, but no shame to reduce freq and try out reboot cold stable on low voltages still clueless why 8000 isnt reboot stable low score cause 253w limit and underclocked cpu, is how i daily it its on openbenchtable

tRDRD_sg higher than 8 is just a sin thats why i said no sense, cause 8 will *always*(im 99,9% certain) work and its important for performance(as per bzoid vid)

Since I started unfortunatelly its my job to try fix it. I apologyze if i was bit toxic. Discussing is the hardest thing in earth.. People will have confidence in their thoughts, defend their claims, have personal attachment etc. Some people "refuge" is this forum, even not being german. Ppl...

there is not a single scenario in EARTH that tRDRD_dg 8 tWRWR_dg 8 tFAW 32 tRDRD_sg 8 will NOT hurt any test, dont make sense to stretch the unnecessary for testing otherwise people would be recommending test frequency at "Load RAW mhz"(which is like 126+ all timings+) QXE said once that ISNT...

i failed in start using forums once again

auto will be loose enough, ddr5 # ddr4 just stop putting random numbers in some places that has no sense

@echo off cd %~dp0 .\y-cruncher.exe pause:1 stress -D:30 -TL:5400 VT3 this is .bat in folder of ycruncher is what i use, -TL is the time limit in seconds 5400 = 90minutes, i prefer to use duration -D 30seconds because i think ON/OFF is heavier and easier to find errors and pause:1 wont close...

I **think** , who found out about deltas and training giving you better chance to have stability consistency (which i think is vei and vei friends?) wont tell, put X, put Y value, but would prefer to explain, cause every computer part is different, even if same model at the end of the day u...

"Disable vddq training, set 1.38MVDDQ and 1.2VDDQ, 1.15SA, 1.35VDD2, MVDD depends on your timings kinda, usually around 1.56 for 8000C36-48 Then start finding optimal CPU_VDDQ which hovers around 160-220mV from MVDDQ You need to find optimal VDDQ offset between CPU and MEM without VDDQ training...

its small freezes, not full freeze like, after a second it get back

I have a question for the most smarts When in stress testing, I get some freezes Is that a bad sign? Maybe if i dont push ram too much i dont get the freezes im thinking

used trfc mini, if looks correct i will be satisfied for ram

im really demotivated to deep dive cause it will be guesses.. an pc is faster cause he can do instructions faster not cause it has been overclocked higher "grain of salt"xd im more interested in architecture and his awful relationship with scheduler/os but i came to the right place, the...

Its very fine. I dont know what to ask Thing is i dont know what I am looking for. if there is something to look for In past i would disable powerdown and selfrefresh, reading a bit aparently disabling it dont even disable it fully (and lowering the timings make pyprime faster so it does...

Registered in this forum to try my luck finding tips. Im currently on Encore with 7800Gskill Adies I believe in "goal is always to overshoot in defensive side of things instead of always being at 1.0 ratio of cooling/clocks" Im with barrow aluminium heatsinks with holes on top (great btw, 1.5mm...