Suchergebnisse

Since last time we checked i reinstalled the original ILM, i couldnt make TR contact frame to work correctly. Everyone say if you screw it down fully it works perfect but that was not the case with me. Anyway MC SP with ILM, 80-85-85-86-85-79-86 I only do 20min loops cause i only...

Previous run was also with HT Off Edit: As i said opened chrome and back to 1.22 with HT Off as you can see

Sun, 55/42/42 HT Off VDD/Q1.44/1.32 SAT1.14 TX1.14 MC1.35 It passed a quick 10 loop stable, but while VST run faster, VT3 dropped from 1.22 to 1.06... EDIT: I opened chrome and rerun VT3 and went back to 1.22...

Ofc you do, i do my best with my limited free time :) Here you go... With SA at 1.12 speeds were all over the place and failed at loop 5... VDD/Q 1.44/1.32 SA 1.13 TX 1.14 MC 1.35 Now i will try with SA 1.14 One test at a time plz :) I will also run TM5

LLC - Auto Min/Max CPU Cache - Auto Global Core Svid - Auto CPU switch freq - Auto SA at 1.15 fail after 5 sec, keep increasing by 0.01v? 7800 seems to work no matter what. Either at auto, low volt or high volt. I will try the same voltages at 7800 also.

Everything as you said and SA 1.12v as tibcsi suggested boot fine. But failed instantly.

Now I use LLC5, change it? Min/Max CPU Cache 44/44, change? Global Core Svid to Auto? IVR VDDQ_IMC 1160mV, TX? IVR VDD(2)_CPU 1350, MC?

Restarted to save the bios for Veii and doesnt seem to have the drop now, weird...

It can pass everything and CB15 Extreme no issues. I feed it with 1.1208-1.137v under load just for VST/VT3 while it only needs like 1.09-1.1v for 56/44/44 I think it only drops while at idle. Dont know if it should do that or not though.

Tested as you suggested. Both dimms installed. Each disabled through bios. SlotA Enabled/SlotB Disabled SlotA Disabled/SlotB Enabled SlotA+B Enabled

After spending so much time trying to get 8000 stable, I tested each dimm on each slot alone. One dimm on each slot at 8000c36 VDD/VDDQ 1.47/1.41 (1.45/1.40 also TM5 stable) SAT 1.20 (bios value) TX1.29 (bios value) MC 1.4125 (bios value) VDDQ training off/MRC fast boot off/fast boot off...

I am testing VST/VT3 for mem stability. So i changed PL1 256w/PL2 320w/ICC MAX 400A/IA VR MAX 1600mv/AC LL Auto Now Cine23 run at 56/44/44 1.172v-1.181v 253w and VST at 55/44/44 1.163-1.172 270w which is far more than it needs. Which option shall i use in OCTool to link you the VF curve?

The Core 1 does not have springs. Tomorrow i ll see if i have any thermal paste left and try to remount. So i can keep LLC 5 and just have AC LL/DC LL at auto? I want to keep PL1/PL2 as low as possible to prevent any kind of degradation till i have my mem tuned. Thats why i keep both Pcores...

Sadly the Apex is in the case and cant check if its any wrapped or not. I use an Alphacool Core 1 cpu block + backplate. Shall i tighen the TR frame at the max, and block + backplate go by hand till it start to get resistance? Does this sound good? Btw TR frame uses the boards ILM screws, does...

Got some free time this morning, coffee and DDR5 :) Managed to gain some stablity finally... VDD/VDDQ 1.46/1.41 SA 1.18 TX 1.30 MC 1.425 56/44/44 HT Off VDDQ ICCMAX 15 Unlimited ICCMAX Dis CPU CUrrent Limit 400 PL1/PL2 250w/250w IA AC 0.01 IA DC 0.82 LLC 5 IA VR Volt Limit 1550 Does...

@Veii Got a new 14900KS and have hard time getting 8000 VST/VT3 stable. I remembered you suggesting to run MC SP x 5 to see how constant are the values. So i did that and got, 80-86-80-84-87. I use a TR contact frame, so this might be the issue? Shall i change to original ILM and retry? BTW...

I am back again after some time, with a new 14900KS this time. A crappy one ofc, but new not the least :) Encore on 9905 bios. Up to 7800C36 its stable with everything at auto. 8000 on the other hand is not. Today I had some time to tweak with not much success because I'm bad at mem oc. But got...

I see, do I have to undervolt all V/F points? Any recommendation how to start/test?

@Veii I set ICCMAX at 320A as you suggested and my clocks drop to 51/40/44 - 235w Is this how its supposed to work or i do something wrong?

Because I don't have much free time to test for hours. And I also only use my pc for browsing/gaming. When/if I manage to get 8000 reboot stable for at least 10 loops then I will test for longer. As I said VDDQ Training is disabled. On TM5 I get no errors that's why I didn't post it. Another guy...