Das hab' ich schon verstanden, aber wozu willst du 120Hz ohne die FPS, daher wollte ich es nur erwähnen.
ForceFullscreen = Vollbild erzwingen. Könnte meinen, dass das Game nicht mehr in 'nem Fenster startet, das hat der Dev jedenfalls auch mal in den Kommies erwähnt. Wie gesagt: Finger weglassen, da es noch nicht benutzt werden soll/kann.
Also ich benutze es und es läuft ohne Probleme, naja 120hz bringen dir auch bei 30 FPS was, das Bild ist immerhin ruhiger und die kamere verschmiert nicht so beim drehen.
Sieht jetzt um einiges besser aus auch mit dem AF und co.
Bei mir schauts jetzt so aus.
###############################################################################
# Graphics Options
###############################################################################
# internal rendering resolution of the game
# higher values will decrease performance
renderWidth 1920
renderHeight 1080
# SMAA1x toggle and quality setting
# 0 = off (best performance, worst IQ)
# 1 = low
# 2 = medium
# 3 = high
# 4 = ultra (worst performance, best IQ)
smaaQuality 4
# Enable and set the strength of the SSAO effect (all 3 settings have the same performance impact!)
# 0 = off
# 1 = low
# 2 = medium
# 3 = high
ssaoStrength 0
############# Depth of field
# Depth of Field resolution override, possible values:
# 0 = no change from default (DoF pyramid starts at 512x360)
# 540 = DoF pyramid starts at 960x540
# 810 = DoF pyramid starts at 1440x810
# 1080 = DoF pyramid starts at 1920x1080
# 2160 = DoF pyramid starts at 3840x2160
# higher values will decrease performance
# do NOT set this to the same value as your vertical rendering resolution!
dofOverrideResolution 810
# Depth of Field scaling override (NOT RECOMMENDED)
# 0 = DoF scaling enabled (default, recommended)
# 1 = DoF scaling disabled (sharper, worse performance, not as originally intended)
disableDofScaling 0
# Depth of field additional blur
# allows you to use high DoF resolutions and still get the originally intended effect
# suggested values:
# o (off) at default DoF resolution
# 0 or 1 at 540 DoF resolution
# 1 or 2 above that
# 3 or 4 at 2160 DoF resolution (if you're running a 680+)
dofBlurAmount 0
###############################################################################
# HUD options
###############################################################################
# Enable HUD modifications
# 0 = off (default) - none of the options below will do anything!
# 1 = on
enableHudMod 0
# Remove the weapon icons from the HUD
# (you can see which weapons you have equipped from your character model)
enableMinimalHud 1
# Scale down HuD, examples:
# 1.0 = original scale
# 0.75 = 75% of the original size
hudScaleFactor 0.75
# Set opacity for different elements of the HUD
# 1.0 = fully opaque
# 0.0 = fully transparent
# Top left: health bars, stamina bar, humanity counter, status indicators
hudTopLeftOpacity 0.8f
# Bottom left: item indicators & counts
hudBottomLeftOpacity 0.75f
# Bottom right: soul count
hudBottomRightOpacity 0.0f
###############################################################################
# Window & Mouse Cursor Options
###############################################################################
# borderless fullscreen mode
# make sure to select windowed mode in the game settings for this to work!
# 0 = disable
# 1 = enable
borderlessFullscreen 0
# disable cursor at startup
# 0 = no change
# 1 = off at start
disableCursor 1
# capture cursor (do not allow it to leave the window)
# 0 = don't capture
# 1 = capture
# (this also works if the cursor is not visible)
captureCursor 0
###############################################################################
# Save Game Backup Options
###############################################################################
# enables save game backups
# 0 = no backups
# 1 = backups enabled
# backups are stored in the save folder, as "[timestamp]_[original name].bak"
enableBackups 0
# backup interval in seconds (1500 = 25 minutes)
# (minimum setting 600)
backupInterval 1500
# maximum amount of backups, older ones will be deleted
maxBackups 10
###############################################################################
# Texture Override Options
###############################################################################
# enables texture dumping
# you *only* need this if you want to create your own override textures
# textures will be dumped to "dsfix\tex_override\[hash].tga"
enableTextureDumping 0
# enables texture override
# textures in "dsfix\tex_override\[hash].png" will replace the corresponding originals
# will cause a small slowdown during texture loading!
enableTextureOverride 0
###############################################################################
# Other Options
###############################################################################
# skip the intro logos
# this should now be slightly more stable, but should still be
# the first thing to disable in case you experience any problems
skipIntro 1
# change the screenshot directory
# default: . (current directory)
# example: C:\Users\Peter\Pictures
# directory must exist!
screenshotDir .
# override the in-game language
# none = no override
# en-GB = English, fr = French, it = Italian, de = German, es = Spanish
# ko = Korean, zh-tw = Chinese, pl = Polish, ru = Russian
# this does not work in Windows XP!
overrideLanguage none
# Dinput dll chaining
# if you want to use another dinput8.dll wrapper together
# with DSfix, rename it (e.g. "dinputwrapper.dll") and put the new name here
dinput8dllWrapper none
# dsmfix.dll
# D3D adapter override
# -1 = no override
# N = use adapter N
# this setting is for multiple (non-SLI/crossfire) GPUs
# everyone else should leave it at -1
d3dAdapterOverride -1
# Log level - 0 to 11, higher numbers mean more logging
# only enable for debugging
logLevel 0
###############################################################################
# The settings below are not yet ready to use!!
###############################################################################
# texture filtering override (NOT RECOMMENDED)
# 0 = no change
# 1 = enable supersampling by downscaling (use only if you need it!)
# 2 = full AF override (may degrade performance, currently implemented badly, do not enable)
# if in doubt, leave this at 0
# you do not need this this if you override filtering in the driver, which is a better option
filteringOverride 2
# You can only set either forceFullscreen or forceWindowed (or neither)
# 0 = off, 1 = on
forceWindowed 0
forceFullscreen 1
# The following settings are only functional if either forceFullscreen or forceWindowed is enabled
# The display width/height
presentWidth 1920
presentHeight 1080
# turn on/off Vsync
enableVsync 1
# adjust display refresh rate in fullscreen mode - this is NOT linked to FPS!
fullscreenHz 120
Grüße
Sharie
.