Follow along with the video below to see how to install our site as a web app on your home screen.
Anmerkung: this_feature_currently_requires_accessing_site_using_safari
Jipp, sind fünf. Einer noch nagelneu und unausgepackt.5 Kreuze hast du auch 5 mora ?
Habe die 200er und ein custom pro Mod mit 9x140er für schnell mal tauschen, klappt gut.Na mit den 4A20 ist das schon viel einfacher als mit 9x P14. Mir wäre es den Aufpreis aber nicht wert.
Garnicht, aber es gab von einem User ein 3D gedruckten Mount für die 200er.Wie habt ihr eigentlich das Quadro am Mora befestigt?
Proof of concept works fine. There is still room for QOL improvement with the design. This requires low profile molex connector to fit under the cover, and of course only works with nfa20.
Anhang anzeigen 656948
Anhang anzeigen 656949
Anhang anzeigen 656950
Gefunden habe ich nur das hier.v2 bracket design has been minimalized. This works well.
Anhang anzeigen 657284
there should be one more piece to support the quadro during plugging and unplugging - I will work on that.
and looking from the side now, if you could use @Midium pcb and @deveth0 neutrik cable, you could have a VERY nice and tidy Mo-Ra.
You're getting on well ...
My German is as good as Google's. Without Google you all may as well be speaking German to my English. : D
My idea is to make a harness for the mora. this allows all pieces to be plugged and unplugged individually. This adds extra cost and complexity, but yields to a more serviceable part in my opinion.
2. I connect the fans by tapping directly into 12v / GND from the socket. This supplies clean, stable power at all times and you don't end up with fans that flutter when starting (one of my D5 Next can only start three fans. The fourth always flickers). I do this by creating two additional four pin male fan sockets to split power and pwm circuits. One socket provides the power and the other socket is connected to a fan cable that goes to one D5 Next with rpm and pwm. When the power is tapped from the neutrik and the rpm / pwm is tapped from the D5 Next, this creates one single socket for all 8 nfa fans to connect to. Maybe this picture of the mora cover will help.
Anhang anzeigen 657967
For 12v / 5v / GND connection I use a 6 pin atx connector because this is a better connector than four pin molex, and the connector is small enough to pass through the hole thats required to be drilled in the mora grill cover. Otherwise, removing the socket would require de-pinning the molex and defeats the easily serviceable aspect that I want. The USB connection also gathers 5v and GND from a splice in the wires after the neutrik socket.
3. You can see above how the fans receive connection. They require 12v and GND from the neutrik socket, and a single RPM and PWM connection from one of your pumps. in the photo above, the single four pin connector with ONLY two wires is the rpm / pwm connection to the D5 Next. You can see how that feeds into the connection with FOUR wires to connect to the fans. You can see that the FOUR wire connector also taps 12v and GND from the ATX connector (which taps the neutrik socket). Below is a photo of the connections on the harness for the mora.
Anhang anzeigen 657970
4. You can ground the neutrik socket exactly how your illustration is drawn. My understanding for this extra wire is just a drain wire for shielding the USB data thats transmitted within the cable. Someone like @ deveth0 surely knows more about this than me though. However, this is not 100% necessary. I would do this if transmitting vulnerable data for some distance, but its hardly required and can be safely overlooked for just a mora project.
9. heat shrinking over the soldered terminals is not required, but does lend to a better finish over all imo. The distances are great enough between pins that there is no chance of arching if done correctly. Also, "don't poke your screwdriver around in there with no insulation."
I've added the bracket to thingiverse . I am new to sharing files so please tell me if there's a problem.
Anhang anzeigen 657999
Also for the quadro friends, I've added it here .
@RaphaFluffa I'm struggling, but finding out now the hard way that both d5 next need power, ground, and data wires through the hubby to work in aquasuite. please add the red and black wires to your diagram/plans.
Hubby7 und Quadrohalter nehmen ich gerne nehmen, musst dann nur sagen was du dafür haben möchtest + Bierzuschuss 😁Wer braucht denn so nen Mount? Eventuell kann ich die Woche nen paar drucken ...
Oder in Österreich die MoRa Schanze.Wer kennt nicht die legendäre N24-Doku "Angriff derWolfsMora-Rudel"?
Ich brauch auch mal nen zweiten...
Hier bitte 3 wenn möglich.Wer braucht denn so nen Mount? Eventuell kann ich die Woche nen paar drucken ...
Nutze die Wandhalerung bisher zwar selbst nicht (liegt aber noch hier rum) - hier nutzen es jedoch viele. Scheint daher gut zu funktionieren, wenn man gut ausmisst 😅.ist das Original Mounting System zu empfehlen, oder lieber auf ein Regal stellen ?
Ich nutze die Füsse und Wandhalterung (mit Filzschutz für Tischfüsse) zusammen, kann den dann neben/an den PC stellen, auf die Fensterbank, an die Wand oder auf nein Schränkchen unter das Fenster legen.Nutze die Wandhalerung bisher zwar selbst nicht (liegt aber noch hier rum) - hier nutzen es jedoch viele. Scheint daher gut zu funktionieren, wenn man gut ausmisst 😅.
Jipp, sind fünf. Einer noch nagelneu und unausgepackt.
Beitrag automatisch zusammengeführt:
Wie habt ihr eigentlich das Quadro am Mora befestigt?
Wer braucht denn so nen Mount? Eventuell kann ich die Woche nen paar drucken ...