[Sammelthread] GigaByte GA-EP45[T]-UD3P / UD3R / UD3 (Intel P45) [3]

Status
Für weitere Antworten geschlossen.
Wenn Du diese Anzeige nicht sehen willst, registriere Dich und/oder logge Dich ein.
Arg,das sollte unser kleines geheimnis bleiben *lach*^^

Joar,für 100 inkl Pretested bekommt man das normal nich,und dann auch noch eine private msn Hotline inklusive:fresse:

Ich will wie gesagt als aller erstes 500x8 Fahren,aber erstmal da haben.
 
Zuletzt bearbeitet:
Code:
MB Intelligent Tweaker(M.I.T.)

Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 8x
Fine CPU Clock Ratio.....................:.+0.50
CPU Frequency ...........................: 4003,50
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 471MHz
PCI Express Frequency (Mhz) .........: 100Mhz
C.I.A. 2.......................................: Disabled
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 900mv
PCI Express Clock Drive.................: 800mv
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Turbo]
Extreme Memory Profile (X.M.P.).....: auto
(G)MCH Frequency Latch...............: 333
System Memory Multiplier ..............: 2.00B
Memory Frequency (Mhz) ..............: 942Mhz


DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................: 5
tRCD .........................................: 5
tRP'...........................................: 5
tRAS..........................................: 15
Advanced Timing Control [Press Enter]
tRRD...........................................: 4
tWTR..........................................: 4
tWR............................................: 8
tRFC...........................................: 56
tRTP...........................................: 4
Command Rate (CMD) ....................: Auto 

Channel A

Channel A Timings Settings [Press Enter]
Static tRead Value.........................: auto
tRD Phase0 Adjustmen....................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto
tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training........................: auto

Channel A Driving Settings [Press Enter]
Driving Strength Profile.................: Auto
Data Driving Pull-Up Level.............: Auto
Cmd Driving Pull-Up Level..............: Auto
Ctrl Driving Pull-Up Level...............: Auto
Clk Driving Pull-Up Level................: Auto

Data Driving Pull-Down Level..........: Auto
Cmd Driving Pull-Down Level...........: Auto
Ctrl Driving Pull-Down Level............: Auto
Clk Driving Pull-Down Level.............: Auto

Channel B

Channel B Timings Settings [Press Enter]
Static tRead Value.........................: auto
tRD Phase0 Adjustmen....................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto

tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Trd2rd(Different Rank)....................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training........................: Auto

Channel B Driving Settings [Press Enter]
Driving Strength Profile.................: Auto
Data Driving Pull-Up Level..............: Auto
Cmd Driving Pull-Up Level...............: Auto
Ctrl Driving Pull-Up Level................: Auto
Clk Driving Pull-Up Level.................: Auto

Data Driving Pull-Down Level...........: Auto
Cmd Driving Pull-Down Level............: Auto
Ctrl Driving Pull-Down Level............: Auto
Clk Driving Pull-Down Level..............: Auto

Motherboard Voltage Control:

Loadline Calibration.………................ Disabled
CPU Vcore….……….........................: 1.35000
CPU Termination…..... 1.200V*.......: 1.30
CPU PLL…………………....1.500V*.......: 1.5
CPU Referen.…………....0.760V*.......: 0.878
MCH/ICH
MCH Core…………….....1.100V...........: 1,30
MCH Reference….…….0.760V...........: 0.863
MCH/DRAM Ref.…......0.900V...........: auto
ICH I/O……………….....1.550V............: auto
ICH Core…………...……1.100V............: auto
DRAM
DRAM Voltage ……....1.800V............: 2,1
DRAM Termination .…0.900V............: auto
Channel A Reference 0.900V............: auto
Channel B Reference 0.900V............: auto

so da isses
 
Er hat E8400 ^^
Static tRead Value.........................: 10
 
Zuletzt bearbeitet:
Könnte jemand mal so als groben Vergleichswert messen was Euer Quad@4Ghz bzw das Gesamtsystem mit LinX konsumiert?

Bei meinem Sys kommen 382W zusammen, Prime Small 315.

Mir ist bewusst das sich unsere Systeme in den seltensten Fällen gleichen, nur interessehalber. :)

Habe meine 4 GHZ Settings inzw gefunden...Prime & Linx stabil. Braucht leider viel Spannung und die Temps sehen entsprechend aus..

Code:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio .......................: 8x
Fine CPU Clock Ratio...................:.+0.5
CPU Frequency .........................: 4.00 Ghz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 471MHz
PCI Express Frequency (Mhz) .........: Auto
C.I.A. 2.......................................: Disabled
Advanced Clock Control [Press Enter]
CPU Clock Drive.......................: 800mv
PCI Express Clock Drive...............: 900mv
CPU Clock Skew (ps)...................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance....................: [Standard]
Extreme Memory Profile (X.M.P.)........: disabled
(G)MCH Frequency Latch.................: 400
System Memory Multiplier ..............: 2.00 D
Memory Frequency (Mhz) ................: 942 Mhz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time..............................: 5
tRCD .........................................: 5
tRP'..........................................: 5
tRAS..........................................: 15
Advanced Timing Control [Press Enter]
tRRD...................................: Auto
tWTR...................................: Auto
tWR....................................: Auto
tRFC...................................: Auto
tRTP...................................: Auto
Command Rate (CMD) ....................: Auto
Channel A

Channel A Timings Settings [Press Enter]
Static tRead Value.....................: 10
tRD Phase0 Adjustmen...................: Auto
tRD Phase1 Adjustment..................: Auto
tRD Phase2 Adjustment .................: Auto
tRD Phase3 Adjustment..................: Auto
Trd2rd(Different Rank).................: Auto
Twr2wr(Different Rank).................: Auto
Twr2rd(Different Rank).................: Auto
Trd2wr(Same/Diff Rank).................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training......................: Auto
Channel A Driving Settings [Press Enter]
Driving Strength Profile.................: Auto

Data Driving Pull-Up Level.............: Auto
Cmd Driving Pull-Up Level..............: Auto
Ctrl Driving Pull-Up Level.............: Auto
Clk Driving Pull-Up Level..............: Auto

Data Driving Pull-Down Level..........: Auto
Cmd Driving Pull-Down Level...........: Auto
Ctrl Driving Pull-Down Level..........: Auto
Clk Driving Pull-Down Level...........: Auto

Channel B

Channel B Timings Settings [Press Enter]
Static tRead Value......................: 10
tRD Phase0 Adjustmen....................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto

tRD Phase3 Adjustment..................: Auto
Trd2rd(Different Rank).................: Auto
Twr2wr(Different Rank).................: Auto
Trd2rd(Different Rank).................: Auto
Trd2wr(Same/Diff Rank).................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training....................: Auto
Channel B Driving Settings [Press Enter]
Driving Strength Profile................: Auto

Data Driving Pull-Up Level..............: Auto
Cmd Driving Pull-Up Level...............: Auto
Ctrl Driving Pull-Up Level..............: Auto
Clk Driving Pull-Up Level...............: Auto

Data Driving Pull-Down Level...........: Auto
Cmd Driving Pull-Down Level............: Auto
Ctrl Driving Pull-Down Level...........: Auto
Clk Driving Pull-Down Level.............: Auto

{U]Motherboard Voltage Control{/U]
Loadline Calibration.………...........: Disabled
CPU Vcore….……….....................: 1,425V
CPU Termination…..... 1.200V*......: 1,28V
CPU PLL…………………....1.500V*..........: 1,50V
CPU Referen.…………....0.76V*.........: 0.85
MCH/ICH
MCH termination...1.100V...........: 1,3V
MCH Reference….…….0.760V...........: 0,89
MCH/DRAM Ref.…......0.900V.........: Normal
ICH I/O……………….....1.50V............: 1,5V
ICH Core…………...……1.100V............: 1,1V
DRAM
DRAM Voltage ……....1.800V.............: 2,1V
DRAM Termination .…0.900V.............: Normal
Channel A Reference 0.900V............: Normal
Channel B Reference 0.900V............: Normal
 
Zuletzt bearbeitet:
Code:
MB Intelligent Tweaker(M.I.T.)

Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 8x
Fine CPU Clock Ratio.....................:.+0.50
CPU Frequency ...........................: 4003,50
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 471MHz
PCI Express Frequency (Mhz) .........: 100Mhz
C.I.A. 2.......................................: Disabled
Advanced Clock Control [Press Enter]
[B][COLOR="Red"]CPU Clock Drive...........................: 900mv tauschen 800mV
PCI Express Clock Drive.................: 800mv tauschen 900 mV[/COLOR][/B]
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Turbo]
Extreme Memory Profile (X.M.P.).....: auto
(G)MCH Frequency Latch...............: 333
System Memory Multiplier ..............: 2.00B
Memory Frequency (Mhz) ..............: 942Mhz


DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................: 5
tRCD .........................................: 5
tRP'...........................................: 5
tRAS..........................................: 15
Advanced Timing Control [Press Enter]
tRRD...........................................: 4
tWTR..........................................: 4
tWR............................................: 8
tRFC...........................................: 56
tRTP...........................................: 4
Command Rate (CMD) ....................: Auto 

Channel A

Channel A Timings Settings [Press Enter]
Static tRead Value.........................: auto
tRD Phase0 Adjustmen....................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto
tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training........................: auto

Channel A Driving Settings [Press Enter]
Driving Strength Profile.................: Auto
Data Driving Pull-Up Level.............: Auto
Cmd Driving Pull-Up Level..............: Auto
Ctrl Driving Pull-Up Level...............: Auto
Clk Driving Pull-Up Level................: Auto

Data Driving Pull-Down Level..........: Auto
Cmd Driving Pull-Down Level...........: Auto
Ctrl Driving Pull-Down Level............: Auto
Clk Driving Pull-Down Level.............: Auto

Channel B

Channel B Timings Settings [Press Enter]
Static tRead Value.........................: auto
tRD Phase0 Adjustmen....................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto

tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Trd2rd(Different Rank)....................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training........................: Auto

Channel B Driving Settings [Press Enter]
Driving Strength Profile.................: Auto
Data Driving Pull-Up Level..............: Auto
Cmd Driving Pull-Up Level...............: Auto
Ctrl Driving Pull-Up Level................: Auto
Clk Driving Pull-Up Level.................: Auto

Data Driving Pull-Down Level...........: Auto
Cmd Driving Pull-Down Level............: Auto
Ctrl Driving Pull-Down Level............: Auto
Clk Driving Pull-Down Level..............: Auto

Motherboard Voltage Control:

Loadline Calibration.………................ Disabled
CPU Vcore….……….........................: 1.35000
CPU Termination…..... 1.200V*.......: 1.30
CPU PLL…………………....1.500V*.......: 1.5
[B][COLOR="Red"]CPU Referen.…………....0.760V*.......: 0.878 eins runter[/COLOR][/B]
MCH/ICH
MCH Core…………….....1.100V...........: 1,30
MCH Reference….…….0.760V...........: 0.863
MCH/DRAM Ref.…......0.900V...........: auto
ICH I/O……………….....1.550V............: auto
ICH Core…………...……1.100V............: auto
DRAM
DRAM Voltage ……....1.800V............: 2,1
DRAM Termination .…0.900V............: auto
Channel A Reference 0.900V............: auto
Channel B Reference 0.900V............: auto

so da isses


probier mal...wenn das nicht klappt...setz mal Static tRead Value.........................: auto auf 10 oder turbo auf standard
 
Zuletzt bearbeitet:
Könnte jemand mal so als groben Vergleichswert messen was Euer Quad@4Ghz bzw das Gesamtsystem mit LinX konsumiert?

Bei meinem Sys kommen 382W zusammen, Prime Small 315.

Mir ist bewusst das sich unsere Systeme in den seltensten Fällen gleichen, nur interessehalber. :)

Habe meine 4 GHZ Settings inzw gefunden...Prime & Linx stabil. Braucht leider viel Spannung und die Temps sehen entsprechend aus..
Ich brauch 1.32 MCH also was willst du? :d bis auf die Vcore ist alles ok VTT hab ich auch so viel gebraucht
 
Code:
MB Intelligent Tweaker(M.I.T.)

Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 8x
Fine CPU Clock Ratio.....................:.+0.50
CPU Frequency ...........................: 4003,50
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 471MHz
PCI Express Frequency (Mhz) .........: 100Mhz
C.I.A. 2.......................................: Disabled
Advanced Clock Control [Press Enter]
[COLOR="Red"]CPU Clock Drive...........................: 900mv tauschen 800mV
PCI Express Clock Drive.................: 800mv tauschen 900 mV[/COLOR]
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Turbo]
Extreme Memory Profile (X.M.P.).....: auto
(G)MCH Frequency Latch...............: 333
System Memory Multiplier ..............: 2.00B
Memory Frequency (Mhz) ..............: 942Mhz


DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................: 5
tRCD .........................................: 5
tRP'...........................................: 5
tRAS..........................................: 15
Advanced Timing Control [Press Enter]
[COLOR="Red"]tRRD...........................................: auto
tWTR..........................................: auto
tWR............................................: auto
tRFC...........................................: auto
tRTP...........................................: auto
Command Rate (CMD) ....................: Auto [/COLOR]

Channel A

Channel A Timings Settings [Press Enter]
Static tRead Value.........................: auto
tRD Phase0 Adjustmen....................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto
tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training........................: auto

Channel A Driving Settings [Press Enter]
Driving Strength Profile.................: Auto
Data Driving Pull-Up Level.............: Auto
Cmd Driving Pull-Up Level..............: Auto
Ctrl Driving Pull-Up Level...............: Auto
Clk Driving Pull-Up Level................: Auto

Data Driving Pull-Down Level..........: Auto
Cmd Driving Pull-Down Level...........: Auto
Ctrl Driving Pull-Down Level............: Auto
Clk Driving Pull-Down Level.............: Auto

Channel B

Channel B Timings Settings [Press Enter]
Static tRead Value.........................: auto
tRD Phase0 Adjustmen....................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto

tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Trd2rd(Different Rank)....................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training........................: Auto

Channel B Driving Settings [Press Enter]
Driving Strength Profile.................: Auto
Data Driving Pull-Up Level..............: Auto
Cmd Driving Pull-Up Level...............: Auto
Ctrl Driving Pull-Up Level................: Auto
Clk Driving Pull-Up Level.................: Auto

Data Driving Pull-Down Level...........: Auto
Cmd Driving Pull-Down Level............: Auto
Ctrl Driving Pull-Down Level............: Auto
Clk Driving Pull-Down Level..............: Auto

Motherboard Voltage Control:

Loadline Calibration.………................ Disabled
CPU Vcore….……….........................: 1.35000
CPU Termination…..... 1.200V*.......: 1.30
CPU PLL…………………....1.500V*.......: 1.5
CPU Referen.…………....0.760V*.......: 0.878 
MCH/ICH
MCH Core…………….....1.100V...........: 1,30
[COLOR="#ff0000"]MCH Reference….…….0.760V...........: 0.863 eins hoch[/COLOR]
MCH/DRAM Ref.…......0.900V...........: auto
[COLOR="#ff0000"]ICH I/O……………….....1.550V............: 1,5V
ICH Core…………...……1.100V............: 1,1V[/COLOR]
DRAM
DRAM Voltage ……....1.800V............: 2,1
DRAM Termination .…0.900V............: auto
Channel A Reference 0.900V............: auto
Channel B Reference 0.900V............: auto

von cole abgeleitet mit noch nem anderen ansatz! bitte unterschiede beachten...sag bitte noch was du für ram hast!!!
 
Zuletzt bearbeitet:
Markiers doch bitte rot ^^ ich erkenn, dass du die MCH frequency latch verändert hast aber ok
 
corsair dominator 2x1GB 1066

so cole hab es so gemacht, er bootet nicht, gleich mal omc`s werte testen
 
Habs bei mir auch mal mit den von Cole angegebenen Werten versucht. Bootet ebenfalls nicht.
Hab dann die 5-5-5-15 auf 5-5-5-18 geändert. Siehe da, bootet ohne Probleme.
OCZ CTX Platinum 1066er

Werd mal Primeln mit den Werten....
 
wenn das net klappt...bitte mal zu meinen einstellungen:
static tread auf 11
performance enhanced auf standard
mch frequency latch auf 400 -> und teiler auf 942MHz RAM-Takt einstellen!
tras auf 18 stellen

bitte noch bios-version angeben!
 
keine Chance....freeze...Bluescreen....Ende

hätt mich auch gewundert mit der Spannung und meiner CPU.
 
Mal ganz kurze frage:Bei mir steht CPU Clock Drive und PCI-Express beides auf 700mv.
Sollte das geändert werden da ich sehe daß es scheinbar alle anderen auf 800mv und für den PCIe auf 900mv haben?
 
@ mrbo

bitte ebenfalls komplette bios-infos posten...dazu welches bios
 
???
Bios ist F8.
Biosinfo...hatte die Werte von Cole eingetragen. Oder was meinst du ?
 
harry also ich hab optimized settings geladen, mit F7, dann müsste es da stehn
 
ich meine komplett alles was du eingetragen hast...siehe der post bios kram

@hardy: nach bios reset stellt sich das auf die werte die "alle" haben
 
Will ja nicht nerven, aber weiß bis heute nicht, wie ich meine Werte da eintragen soll.

Andere Frage,
meinst du, das meine CPU mit weniger Spannung als bisher auskommen könnte?

Habe eigentlich sauber geprimelt (Thread gelesen), und dabei rausgefunden, was sie braucht um stabil zu laufen. Denke die 1,3375 V im Bios bei 3,8 GHz sind nicht wirklich zu umgehen.......
wäre natürlich super, habe aber eigentlich schon alles getestet .

Lasse mich aber gerne eines besseren belehren
 
Zuletzt bearbeitet:
du drückst auf den code-button und dann fügst das einfach ein!!!
 
Code:
MB Intelligent Tweaker(M.I.T.)

Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 8x
Fine CPU Clock Ratio.....................:.+0.50
CPU Frequency ...........................: 4003,50
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 471MHz
PCI Express Frequency (Mhz) .........: 100Mhz
C.I.A. 2.......................................: Disabled
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mv
PCI Express Clock Drive.................: 900mv
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: auto
(G)MCH Frequency Latch...............: 400
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ..............: 942Mhz


DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................: 5
tRCD .........................................: 5
tRP'...........................................: 5
tRAS..........................................: 18
Advanced Timing Control [Press Enter]
tRRD...........................................: Auto
tWTR..........................................: Auto
tWR............................................: Auto
tRFC...........................................: Auto
tRTP...........................................: Auto
Command Rate (CMD) ....................: Auto 

Channel A

Channel A Timings Settings [Press Enter]
Static tRead Value.........................: 11
tRD Phase0 Adjustmen....................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto
tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training........................: auto

Channel A Driving Settings [Press Enter]
Driving Strength Profile.................: Auto
Data Driving Pull-Up Level.............: Auto
Cmd Driving Pull-Up Level..............: Auto
Ctrl Driving Pull-Up Level...............: Auto
Clk Driving Pull-Up Level................: Auto

Data Driving Pull-Down Level..........: Auto
Cmd Driving Pull-Down Level...........: Auto
Ctrl Driving Pull-Down Level............: Auto
Clk Driving Pull-Down Level.............: Auto

Channel B

Channel B Timings Settings [Press Enter]
Static tRead Value.........................: 11
tRD Phase0 Adjustmen....................: Auto
tRD Phase1 Adjustment...................: Auto
tRD Phase2 Adjustment ..................: Auto

tRD Phase3 Adjustment...................: Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Trd2rd(Different Rank)....................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training........................: Auto

Channel B Driving Settings [Press Enter]
Driving Strength Profile.................: Auto
Data Driving Pull-Up Level..............: Auto
Cmd Driving Pull-Up Level...............: Auto
Ctrl Driving Pull-Up Level................: Auto
Clk Driving Pull-Up Level.................: Auto

Data Driving Pull-Down Level...........: Auto
Cmd Driving Pull-Down Level............: Auto
Ctrl Driving Pull-Down Level............: Auto
Clk Driving Pull-Down Level..............: Auto

Motherboard Voltage Control:

Loadline Calibration.………................ Disabled
CPU Vcore….……….........................: 1.35000
CPU Termination…..... 1.200V*.......: 1.30
CPU PLL…………………....1.500V*.......: 1.5
CPU Referen.…………....0.760V*.......: 0.878
MCH/ICH
MCH Core…………….....1.100V...........: 1,30
MCH Reference….…….0.760V...........: 0.903
MCH/DRAM Ref.…......0.900V...........: auto
ICH I/O……………….....1.550V............: 1,5
ICH Core…………...……1.100V............: 1,1
DRAM
DRAM Voltage ……....1.800V............: 2,1
DRAM Termination .…0.900V............: auto
Channel A Reference 0.900V............: auto
Channel B Reference 0.900V............: auto

so hab ich es mal getestet, diesmal bin ich bis vor dem windows ladebalken gekommen, dann bluescreen, dieses mal musste ich aber kein cmos machen
 
kannst mich mal bitte anrufen??? rest machen wir per telefon! festnetz vorhanden...sag bescheid dann schick ich dir nummer per pn!!
 
Bitte mal Posten, wenn bei eurem Telefongespräch was rausgekommen ist.
Bitte dann auch mit den passenden Settings. Würde mich sehr interessieren
 
Status
Für weitere Antworten geschlossen.
Hardwareluxx setzt keine externen Werbe- und Tracking-Cookies ein. Auf unserer Webseite finden Sie nur noch Cookies nach berechtigtem Interesse (Art. 6 Abs. 1 Satz 1 lit. f DSGVO) oder eigene funktionelle Cookies. Durch die Nutzung unserer Webseite erklären Sie sich damit einverstanden, dass wir diese Cookies setzen. Mehr Informationen und Möglichkeiten zur Einstellung unserer Cookies finden Sie in unserer Datenschutzerklärung.


Zurück
Oben Unten refresh