Aja ok, thx...
Ich hab halt nur irgendwie schiss, dass irgendwie die Pipes mit der Zeit futsch gehen un ich noch ma zurückflashen muss?!
Aber geht sowas net au unter windows? Weil ich trau disketten net so ganz, wobei des ja auch von ner Fat partition gehen sollte?
Gruß Moorhuhn87
P.S.: Des stand noch bei dem Gainward Bios dabei:
NVIDIA Firmware Update Utility (Version 05.00)
-- Primary Commands --
Update firmware: nvflash [options] <filename>
Save firmware to file: nvflash [options] --save <filename>
Compare adapter firmware: nvflash [options] --compare <filename>
Update TV data: nvflash [options] --tv <filename>
Display version: nvflash [options] -- version [<filename>]
Erase EEPROM: nvflash [options] --erase
Display firmware bytes: nvflash [options] --display=<bytes>
Check for supported EEPROM: nvflash [options] --check
Write protect EEPROM: nvflash [options] --protecton
Remove write protect: nvflash [options] --protectoff
Change soft straps: nvflash [options] --straps=<straps>
Set IEEE 1394 GUID: nvflash [options] --guid=<guid>
Set IEEE 1394 GUID source: nvflash [options] --guidsource=<location>
List adapters: nvflash [options] --list
-- Commands and Options --
help ? Display this screen.
save b <filename> Read EEPROM and save to <filename>.
compare k <filename> Read EEPROM and compare with <filename>.
tv x <filename> Transfer TV data from file to EEPROM.
version v <filename> Display file version and ~CRC32
(if no filename, acts on display adapter).
erase e Erase the EEPROM.
display d [bytes] Display 256 the first bytes of the EEPROM
(default is 256 bytes)
check c Check for supported EEPROM.
protecton w Write protect EEPROM (only on some EEPROM's).
protectoff r Remove EEPROM write protect (only on some EEPROM's).
straps m <straps> Change soft straps.
format is: AND Mask 0, OR Mask 0, AND Mask 1, OR Mask 1
guid q <guid> Set the IEEE 1394 GUID in the firmware image
(GUID is in the form of 16 hex digits).
guidsource 1 <location> Set the source of the IEEE 1394 GUID.
main - main EEPROM image
dedicated - separate serial EEPROM part
list a List all NVIDIA display adapters found in the system.
nolight l Do not light keyboard LEDs.
overridetype 5 Allow firmware and adapter PCI device ID mismatch.
overridesub 6 Allow firmware and adapter PCI subsystem ID mismatch.
reboot y Reboot the PC after other tasks completed.
keepstraps g Keep the soft straps already present in the EEPROM
after flashing the new image.
romstrap j Override the ROM strap setting to allow flashing an
image when grounding the STRAP_SUB_VENDOR pin.
This allows flashing a corrupted or erased EEPROM.
Note: Make sure there is a physical EEPROM present
when using this option
index i <index> Force a specific device index.
fwindex F <fw index> Index of which firmware image to use from a firmware
bundle.
auto A When possible, run without user intervention.
silence s <level> Silence level:
default All beeps.
#=4 (or 2) No progress beeps.
#=5 (or 1) No beeps.
override o <level> Override safety check level:
default unknown EEPROM | NV adapter aborts application.
level=1 unknown EEPROM acceptable for read operations.
level=2 unknown NV adapter acceptable for read operations.
level=3 Combined effect of 1,2 (cannot write to unknown EEPROM or adapter).
Use a single dash ("-") to use the single letter version of a command.
Use a double dash ("--") to use the longer descriptive version of a command.
Use equals ("=") to specify parameters, with separating commas (",").
-- Sample Usage --
nvflash --index=1 nv30nz.rom
)
