MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio .......................: 9x
Fine CPU Clock Ratio...................:.+0.00
CPU Frequency .........................: 4000Mhz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 445MHz
PCI Express Frequency (Mhz) .........: 100Mhz
C.I.A. 2.......................................: Disabled
Advanced Clock Control [Press Enter]
CPU Clock Drive.......................: 800mv
PCI Express Clock Drive...............: 900mv
CPU Clock Skew (ps)...................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance....................: [Turbo]
Extreme Memory Profile (X.M.P.)........: disabled
(G)MCH Frequency Latch.................: 333
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ................: 990Mhz
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time..............................: 5
tRCD .........................................: 5
tRP'..........................................: 5
tRAS..........................................: 18
Advanced Timing Control [Press Enter]
tRRD..........................3.........: Auto
tWTR...........................3........: Auto
tWR.............................6.......: Auto
tRFC.............................52.....: Auto
tRTP...............................3....: Auto
Command Rate (CMD) .................0...: Auto
Channel A
Channel A Timings Settings [Press Enter]
Static tRead Value.............11......: 10
tRD Phase0 Adjustmen.............0.....: Auto
tRD Phase1 Adjustment.............0....: Auto
tRD Phase2 Adjustment ............0....: Auto
tRD Phase3 Adjustment.............0....: Auto
Trd2rd(Different Rank)............6....: Auto
Twr2wr(Different Rank)............6....: Auto
Twr2rd(Different Rank)............5....: Auto
Trd2wr(Same/Diff Rank)............8....: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training......................: Auto
Channel A Driving Settings [Press Enter]
Driving Strength Profile.................: Auto
Data Driving Pull-Up Level.............: Auto
Cmd Driving Pull-Up Level..............: Auto
Ctrl Driving Pull-Up Level.............: Auto
Clk Driving Pull-Up Level..............: Auto
Data Driving Pull-Down Level..........: Auto
Cmd Driving Pull-Down Level...........: Auto
Ctrl Driving Pull-Down Level..........: Auto
Clk Driving Pull-Down Level...........: Auto
Channel B
Channel B Timings Settings [Press Enter]
Static tRead Value.............11........: 10
tRD Phase0 Adjustmen............0........: Auto
tRD Phase1 Adjustment...........0........: Auto
tRD Phase2 Adjustment ..........0........: Auto
tRD Phase3 Adjustment...........0........: Auto
Trd2rd(Different Rank).......6..........: Auto
Twr2wr(Different Rank).......6..........: Auto
Trd2rd(Different Rank).......5..........: Auto
Trd2wr(Same/Diff Rank).......8..........: Auto
Dimm1 Clock Skew Control...............: Auto
Dimm2 Clock Skew Control...............: Auto
DDR2 Write Training....................: Auto
Channel B Driving Settings [Press Enter]
Driving Strength Profile...............: Auto
Data Driving Pull-Up Level..............: Auto
Cmd Driving Pull-Up Level...............: Auto
Ctrl Driving Pull-Up Level..............: Auto
Clk Driving Pull-Up Level...............: Auto
Data Driving Pull-Down Level...........: Auto
Cmd Driving Pull-Down Level............: Auto
Ctrl Driving Pull-Down Level...........: Auto
Clk Driving Pull-Down Level............: Auto
{U]Motherboard Voltage Control{/U]
Loadline Calibration.………...........: disabled
CPU Vcore….……….....................: musst wohl rausfinden
CPU Termination…..... 1.200V*......: 1,28V
CPU PLL…………………....1.500V*..........: 1,50V
CPU Referen.…………....0.76V*.........: cpu termination *0,67
MCH/ICH
MCH termination...1.100V...........: 1,3V
MCH Reference….…….0.760V...........: cpu termination *0,67
MCH/DRAM Ref.…......0.900V.........: AUTO
ICH I/O……………….....1.50V............: 1,5V
ICH Core…………...……1.100V............: 1,1V
DRAM
DRAM Voltage ……....1.800V.............: 2,10V
DRAM Termination .…0.900V.............: AUTO
Channel A Reference 0.900V............: AUTO
Channel B Reference 0.900V............: AUTO
[b]{U]Advanced Settings[b]{U]
Limit CPUID Max. to 3................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)..............: [ENabled]
CPU Thermal Monitor 2(TM2) ..........: [Enabled]
CPU EIST Function....................: [Enabled]
Virtualization Technology............: [Disabled]