Genie BIOS Setting
Exit Setup shutdown........................... - Mode 2
Shutdown after AC loss........................ - Enabled
AC Shutdown free.............................. - Enabled
O.C. Fail retry Counter....................... - 1
O.C. Fail CMOS Reload......................... - Disabled
CPU Clock Ratio............................... - 8X
CPU N/2 Ratio................................. - Disabled
Target CPU Clock.............................. - 4000 MHz ist sicher bei 1,24 stable!
CPU Clock..................................... - 500 MHz
Boot Up Clock................................. - Auto
CPU Clock Amplitude........................... - 800mV
CPU Clock0 Skew............................... - 0ps
CPU Clock1 Skew............................... - 0ps
DRAM Speed.................................... - 333/667
Target DRAM Speed............................. - DDR2 1001
PCIE Clock.................................... - 100 MHz
CPU Spread Spectrum........................... - Disabled
PCIE Spread Spectrum.......................... - Disabled
CPU Feature
Thermal Management Control.................... - Enabled
PPM (EIST)Mode................................ - Disabled
Limit CPUID MaxVal............................ - Disabled
C1E Function.................................. - Disabled
Execute Disable Bit........................... - Disabled
Virtualization Technology..................... - Enabled
Core Multi-Processing......................... - Enabled
DRAM Timing
Enhance Data Transmitting..................... - Auto
Enhanced Addressing........................... - Auto
T2 Dispatch................................... - Auto
Flex Memory Mode.............................. - Auto
CAS Latency Time (tCL)........................ -Auto
RAS# to CAS# Delay (tRCD)..................... - Auto
RAS# Precharge (tRP).......................... - Auto
Precharge Delay (tRAS)........................ - Auto
All Precharge to ACT.......................... - Auto
REF to ACT Delay (tRFC)....................... - Auto
Performance LVL (Read Delay).................. - Auto
Write to PRE Delay (tWR)...................... - Auto
Rank Write to Read (tWTR)..................... - Auto
ACT to ACT Delay (tRRD)....................... - Auto
Read to Write Delay (tRDWR)................... - Auto
Ranks Write to Write (tWRWR).................. - Auto
Ranks Write to Read (tWRRD)................... - Auto
Read CAS# Precharge (tRTP).................... - Auto
All PRE to Refresh............................ - Auto
Clock Setting Fine Delay
DLL and RCOMP Settings........................ - By Menu
CH1 DRAM Default Skew......................... - Model 3
CH2 DRAM Default Skew......................... - Model 3
RCOMP Setting................................. - Model 1
Fine Delay Step Degree........................ - 70ps
Ch1 Clock Crossing Setting.................... - Auto
DIMM 1 Clock fine delay....................... - current 1542ps
DIMM 2 Clock fine delay....................... - current 1542ps
Ch1 Control0 fine delay....................... - current 190ps
Ch1 Control1 fine delay....................... - current 190ps
Ch1 Control2 fine delay....................... - current 142ps
Ch1 Control3 fine delay....................... - current 126ps
Ch1 Command fine delay........................ - current 300ps
Ch2 Clock Crossing Setting.................... - Auto
DIMM 3 Clock fine delay....................... - current 1542ps
DIMM 4 Clock fine delay....................... - current 1542ps
Ch2 Control0 fine delay....................... - current 16ps
Ch2 Control1 fine delay....................... - current 64ps
Ch2 Control2 fine delay....................... - current 0ps
Ch2 Control3 fine delay....................... - current 0ps
Ch2 Command fine delay........................ - current 120ps
Ch1Ch2 Common Clock Setting................... - Auto
Ch1 RDCAS GNT-Chip Delay...................... - Auto
Ch1 WRCAS GNT-Chip Delay...................... - Auto
Ch1 Command to CS Delay....................... - Auto
Ch2 RDCAS GNT-Chip Delay...................... - Auto
Ch2 WRCAS GNT-Chip Delay...................... - Auto
Ch2 Command to CS Delay....................... - Auto
Voltage Setting
CPU VID Special Add........................... - +175.0mV
DRAM Voltage Control.......................... - 2.100
SB Core/CPU PLL Voltage....................... - 1.55V
NB Core Voltage............................... - 1.2700 [B]auch 1,3....[/B]
CPU VTT Voltage............................... - 1.13V [B]auch 1,20[/B]
Vcore Droop Control........................... - Disabled [B]auch enabled[/B]
Clockgen Voltage Control...................... - 3.45V
CPU GTL 0/2 REF Volt.......................... - 0.63X
CPU GTL 1/3 REF Volt.......................... - 0.63X
North Bridge GTL REF Volt..................... - 0.61X [B]auch 58 getestet wie 67 ..[/B]
FSB Vref...................................... -